Instructions / Assembly

ManualsBrandsHarper & Bright Designs ManualsBedsBlack Wood Frame Queen Size PU Platform Bed with Adjustable Headboard, Hydraulic Storage System, LED Lights and USB Port

Page 1 of 10

ASSEMBLY INSTRUCTION

1. Please read the instructions fully before

assembly. These instructions include

important information which could ensure

correct assembly. We have been working

on providing high quality products for you.

However, in the rare instance that your

product is defective, missing parts or there

are some issues, please don't hesitate to

contact our customer service to submit

parts requirements, assembly suggestion,

or warranty claims, and we will give the

best solution as soon as possible. If

necessary, we need you to provide some

more clear pictures of the issue.

2. Insert the screws in holes and tighten

the screws, but not too tight, 70%~80% is

ok, finally tighten all the screws. If some

issues happened that some screws can

not target to the hole or some parts are

difficult to install, please adjust the

tightness of the screws.

3. 2 people are recommended to finish

TIPS

20R

20L

WF303378/WF303379

Summary of content (10 pages)

PAGE 1
ASSEMBLY INSTRUCTION WF303378/WF303379 TIPS 1. Please read the instructions fully before assembly. These instructions include important information which could ensure correct assembly. We have been working on providing high quality products for you.
PAGE 2
PAGE 3
PAGE 4
This product is not suitable for mattress recessed type. This product is suitable for placing mattresses on the top. IMPORTANT NOTICE OTTOMAN OPERATING INSTRUCTIONS Once your bed frame is completely assembled, the slat unit will not operate correctly unless a mattress is placed on the slat frame. Position the mattress on the slat frame whilst it is in the closed position. PLEASE NOTE - It takes a lot of force to make the initial movement of the ottoman.
PAGE 5
Attention: Do not tighten the screws before completing the entire installation.If you have any difficulty with the installation process, please feel free to contact us. Step 1: E ×4 J ×4 K ×1 Fix the Headboard legs(20L) / (20R) To the headboard(1) With Bolts (E) and Flat Washer (J) by using Allen key (K),you can chose the holes a and b or b and c .
PAGE 6
Step 4: B ×8 K ×1 B Fix the Side Rails (3L)&(3R) to the Head board leg (20L)/(20R) and Footboard (2) with a hex wrench (K) and bolts (B). 1 K 3L 3R 2 Use a hex wrench (K) to connect the Reinforced Pipe (5) to the side member with bolts (A). Step 5: A ×4 B ×8 A K 5 ×1 K 5 16 B Use a hex wrench (K) to fix the metal bracket (16) to the Side Rails and Footboard with bolts (B).
PAGE 7
Step 6: Stick the black non-woven fabric (19)To the bottom of bed 19 Step 7: D H G K J ×6 Bottom view, when connecting 8 and 9, make sure that the holes in the dashed boxes are aligned. ×6 ×1 ×1 9 8 ×6 9 G 9 8 H J 10 8 8 D K 8 Using an Allen wrench (K), install the inner frames (8, 9, and 10) with bolts (D), flat washers (J), and non slip nuts (H).
PAGE 8
Step 8: D F H G K J Headboard Use an Allen wrench (K) to connect the center leg (11) to the center pipe (8) with M6 bolts (F) and flat washers (J). ×6 Leave spacing ×2 ×6 ×1 ×1 Headboard metal frame K metal frame F J ×2 8 Leave spacing Footboard Footboard 11 K D 11 4 8 H 11 G First, use bolts (D) and nuts (H) to connect the side tube (8) to the hinge (4). At this stage, do not fully tighten the bolts (D) to allow for some adjustment between the headboard, pedals and the metal frame.
PAGE 9
Step 10: H ×4 G ×1 17 ×1 Attach the gas struts (7) to the hinge (4) with M8 nuts (H)as shown. As shown in the figure, tie the rope (17) to the Cross Rail for Metal Slat Frame - Footend On the internal frame. 17 H G H G Step 11: P Open the zipper, take out the USB cable, and insert it into the power transformer.
PAGE 10
Operation Instructions of Controller LED light Ⅰ.Specifications: If you can't let the lights work successfully,please check the following: 1.Please check the direction of the connect,try it in the opposite direction,according to the following picture. 2.Please check the remote control,it need you to tear down the plastic septum before use it. 3.If one of the colors is not bright, please check whether the four wires in the plug are skewed, and move the main line to make the four wires flush.