Assembly Instructions Note: Please help to read my instruction before you ready to assemble.
Part List Label Picture Description QTY (PCS) A Backrest 1 B Left Armrest 1 C Right Armrest 1 D Seat 1 E Front Rail 1 F Seat Cushion 1 G Leg 4 PAGE 2 OF 9
Hardware ① Plastic Washer 7 ② Allen Wrench 1 ③ Bolt(M6*20mm) 7 ④ Metal Bracket 3 ⑤ Allen Wrench(S4) 1 Assembly Preparation All Including: x1 x4 x1 x7 x7 x3 x1 NOTICE: -Please read the instruction from cover to cover in detail.Thanks. -Installed by at least two adults -To avoid damaging your furniture ，Please don't assemble on flooring or carpet. -Please assemble on a clean non-marring surface, example for packing foam. -Saving all packaging until have finished.
Assembly Steps OVERVIEW Left Armrest(B) Backrest(A) Right Armrest(C) Leg(G) Seat Cushion(F) Front Rail(E) This Chair has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Chair parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly.
Step 3 Left Armrest(B) Loosen the 3 bolts in Left Armrest(B) around half inch by Allen Wrench( ②). Repeat the same step to loosen 3 bolts in Right Armrest(C). Step 4 Right Armrest(C) Front Rail(E) Left Armrest(B) With the assistance of your partner,slide the hook in the eng of Front Rail(E) into the bolts on the Left Armrest(B) and Right Armrest(C), as shown in Picture.
Step 5 Backrest(A) Loosen the bolt in Backrest(A) around half inch by Allen Wrench( ②). Step 6 Right Armrest(C) Backrest(A) Left Armrest(B) Keep the Backrest(A) and the back of the Left Armrest(B), Right Armrest(C) flat. Slide the Tapered Connectors on the Backrest(A) into the Tapered Connectors on the Left Armrest(B) as shown in the picture. Repeat the same process with the Right Armrest(C).
Step 7 Seat(D ) Front Rail(E ) With the assistance of your partner,lift the rope on the two sides of Seat(D) by hand. Put the Seat(D) on the wood bar of the Front Rail(E) and then slowly place it down as shown above. Note:All the u-shaped iron sheet need clamped to the bolt. Step 8 Right Armrest(C) Left Armrest(B) Backrest(A) Tilt and lay the Chair onto a flat surface. Tighten the Bolts in the bottom of Backrest(A),Left Armrest(B) and Right Armrest(C) by Allen Wrench( ②) as pictured above.
Step 9 Right Armrest(C) Left Armrest(B) Front Rail(E) Change tilt and lay the Chair another side onto a flat surface. Tighten all the Bolts at the end of bottom Left Armrest(B) and Right Armrest(C) by Allen Wrench( ②) as pictured above. Tighten the Bolts fully in a sequential manner. Step 10 Right Armrest(C) Left Armrest(B) Leg(G) Install the Leg(G) at the bottom of Left Armrest (B) and Right Armrest(C) by placing Plastic Washer( ①) on the threaded stem.
Step 11 Seat Cushion(F) Turn the Chair to its upright position. Place the Seat Cushions(F) onto the Chair. Step 12 Your Chair is ready for use. This Chair can only be used on a flat, level surface.
