09-16-09 AL690 Side-Door Hybrid Lift AL600 Universal Hybrid Lift AL650 Hybrid Powerchair Lift w/ Docking Station
UNPACKING THE LIFT y Hardware Pack ALA680 4 - Leveling Pads 4x ft As s em 690 only bl 2x MOUNTING HARDWARE 2B COUTT NT ON RO HA LL ND ER AL600 / AL650 OR VEHICLE HARNESS Li INSTALLATION WASHERS J-HOOKS 2 - 5/16-18 x 4.
WIRING THE VEHICLE IMPORTANT NOTE: IMPROPER WIRING IS THE #1 CAUSE OF PROBLEMS IN THE OPERATION OF A VEHICLE LIFT. FOLLOW THE WIRING INSTRUCTIONS CAREFULLY LOCATED IN THE HARDWARE PACK IS THE VEHICLE WIRING HARNESS. THE HARNESS IS MANUFACTURED TO, AND COMPLIES WITH, THE SAE J1128 REQUIREMENTS. THE WIRE HARNESS IS APPROXIMATELY 23 ft LONG AND WILL ACCOMMODATE MOST VEHICLES. YOUR HEAVY DUTY HARNESS HAS BEEN LEFT UN-ASSEMBLED FOR EASE OF INSTALLATION.
AL650 AL 650 - SETTING DOCK STATION HEIGHT Docking Station Height ONLY PRIOR TO MOUNTING DOCKING PLATE TO CHAIR GROUND CLEARANCE MUST BE GREATER THAN OR EQUAL TO 1.75 INCHES IF GROUND CLEARANCE = HARDWARE USED: ( from hardware pack ) THEN USE: No Spacers 1.75" - 2" MOUNTED ON LIFT FROM FACTORY .25" spacers 2.25" MEASURE DISTANCE OF MOUNTING SURFACE TO GROUND 0.25" 0.25" 1.25" x4 .5" spacers 2.5" 0.50" 0.50" .75" spacers 2.75" 0.25" 0.25" 0.50" 0.50" 1" spacers 3" 1.00" 1.00" 2.
Docking Station Height AL650 ONLY AL 650 - SETTING DOCK STATION HEIGHT REMOVE LOCKING STATION AND INSERT APPROPRIATE NUMBER OF SPACERS. RE-ATTACH TO PLATFORM. CHANGE TO LONGER SCREWS IF NECESSARY. CHANGE TO LONGER SCREWS AS REQUIRED ( CHART ON PREVIOUS PAGE ) NUMBER & TYPE OF SPACERS DEPENDS ON CHAIR’S GROUND CLEARANCE.
Power Chair Preparation AL650 AL 650 - MOUNTING CHAIR PLATE ONLY CHOOSING A LOCATION and MOUNTING THE DOCKING DEVICE PLATE DO NOT ATTEMPT TO USE THIS AUTOMATIC LOCK DOWN DEVICE ON ANY FOLDING, OR TAKE APART CHAIRS UNLESS RECOMMENDED BY HARMAR.
AL600 & AL690 Power Chair or Scooter Preparation CHAIR / SCOOTER PREPARATION THERE ARE 2 OPTIONS ON HOW TO ATTACH THE STRAP HOOKS TO THE CHAIR THAT ARE INCLUDED WITH THE LIFT. ANCHOR PLATE: THE ANCHOR PLATE IS A FLAT PLATE THAT IS 20” LONG WITH A SLOT IN EACH END. THIS PLATE WILL WORK WITH ANY CHAIR OR SCOOTER THAT HAS A CENTER SEAT POST AND ATTACHES TO THE BOTTOM OF THE SEAT. ATTACH THE ANCHOR PLATE BY THE FOLLOWING STEPS: THE ANCHOR PLATE SHOULD EXTEND ABOUT 1-1/2” OUT FROM THE SIDE OF THE CUSHION.
AL 600/650 - INSTALLATION 5 POSITION LIFT SSE LY A FUL APPLICATION: SCOOTER OFFSET LIFT’S POSITION APPLICATION: POWERCHAIR CENTER LIFT’S POSITION MBL ED L EG S OSE FOR P PUR CE REN E F RE PLACE LIFT ON TOP OF LEG AND FOOT PLATE 1 REMOVE 3rd ROW SEAT 7 PLUG IN HAND CONTROLLER 6 ATTACH LIFT BOLT UP FROM UNDER USING THE SUPPLIED BOLT / NUT / WASHER (2) AND BRACKETS AS INDICATED 2 PLACE LEG ASSEMBLY TO VEHICLE HARNESS LOAD LINE (CLOSED DOOR INNER SURFACE) LEAVE ALL HARDWARE LOOSE FOR ADJUSTMENT
AL 690 - INSTALLATION AL600 & AL650 5 POSITION LIFT PLACE LIFT ON TOP OF LEG ASSEMBLIES ADJUST AS NEEDED 1 REMOVE 2nd ROW SEAT 2 PLACE LEG ASSEMBLIES (PASSENGER SIDE EXIT SHOWN) LOAD LINE (CLOSED DOOR INNER SURFACE) 6 ATTACH LIFT LED EMB ASS LEG R A E R BOLT UP FROM UNDER USING THE SUPPLIED BOLT / NUT / WASHER AND BRACKETS AS INDICATED LEAVE ALL HARDWARE LOOSE FOR ADJUSTMENT PURPOSES CENTER IN DOOR WAY 42” 52” REAR LEG LOAD LINE (CLOSED DOOR INNER SURFACE) 3rd ROW SEATING LOCATE REAR LEG 42”to
AL600 Loading a Power Chair AL 600 - LOADING A POWER CAHIR Parking the Chair on the Platform: Before loading the power chair, verify that the platform has been lowered all the way to the ground. Set your chair’s speed control at a slow speed so that you may maneuver comfortably onto the platform. You may drive onto the platform from either side. Park the chair such that it is centered on the platform.
AL600 AL 600 - LOADING A SCOOTER Parking the Scooter on the Platform: Before loading the scooter, verify that the platform has been lowered all the way to the ground. Set your scooter’s speed control at a slow speed so that you may maneuver comfortably onto the platform. You must drive onto the platform from the driver’s side of the vehicle. Park the scooter such that the front wheel(s) is(are) on top of the front wheel scooter adapter.
AL 650 - LOADING A POWER CHAIR Parking the Chair on the Platform: Before loading the power chair, verify that the platform has been lowered all the way to the ground. Set your chair’s speed control at a slow speed so that you may maneuver comfortably onto the platform. Drive the chair onto the platform into the opening of the docking station.
AL 690 - LOADING A POWER CHAIR or MICRO SCOOTER Parking the Chair on the Platform: Before loading the power chair, verify that the platform has been lowered all the way to the ground. Set your chair’s speed control at a slow speed so that you may maneuver comfortably onto the platform. Either back the chair onto the platform, or drive forward depending on the chair's weight displacement. The heaviest portion of the chair needs to be closest to the lifting tower.
SAFETY & MAINTENACE SAFETY: Caution: Do not operate this lift until your dealer has satisfactorily instructed you in the proper operation of the lift. Your Harmar lift has been engineered and designed for years of trouble free use. Although, with everyday use, some parts may become loose or worn. IMPORTANT! Check regularly for any worn, loose or damaged parts of your lift. If anything is observed, DO NOT USE THE LIFT! Contact your dealer or installer of the lift for repairs to be made.
NOTES LIFT MODEL NUMBER: ___________________________________ SERIAL NUMBER : _______________________________________ SERVICE PERFORMED : ______________________________________________________________________ DATE: __________________ SERVICE PERFORMED : ______________________________________________________________________ DATE: __________________ SERVICE PERFORMED : ______________________________________________________________________ DATE: __________________ SERVICE PERFORMED : ___________________
EXPLODED VIEWS 6 1 ASSEMBLY PARTS ITEM QT Y PART NO. DESCRIPTION 0.25 MW: 0.625 OD 1 6 90126A029 2 6 90640A129 NL: 0.25-20 3 6 92949A552 BSCS: 0.25-20 x 2.50 4 6 H600141 5 6 H600151 6 1 H600803 AL600 BASEWHEEL BASE WHEEL SPACER TUBE HPL BASE & LEG DETAIL A (x6) SEE DETAIL A 3 6 5 6 2 6 4 6 ASSEMBLY PARTS ITEM 1 6 1 2 QTY PART NO. 2 0_25-20_LOCK_NUT 90640A129 2 1 1BASE-ASSY AL600 ASSEMBLY PART 1 3 8 92805A242 4 2 92949A540 BSCS: 0.25-20 x 0.
EXPLODED VIEWS 5 2 10 1 8 1 4 2 12 1 3 3 10 1 5 2 13 1 ASSEMBLY PARTS ITEM 2 4 6 1 11 2 1 1 14 1 QT Y PART NO. DESCRIPTION 1 1 2 4 91266A250 SHCS: 10-32 X 0.375 3 3 92949A566 BSCS: 0.25-28 x 1.00 4 2 98306A280 CLEVIS PIN, 3/8" x 2-3/8 L 5 4 ALA21410 FLANGE BUSHING BRZ 3/8X1/2X3/8 6 1 ALA41011_CC L 7 1 ALA60020_QTY_ 2 8 1 ALA60022 H600802 VERTICAL CHAIN 9 2 ALA62099 CHAIN TENSIONER BOLT 1.
EXPLODED VIEWS 2 2 4 1 1 1 3 2 ASSEMBLY PARTS ITE M 5 1 QTY PART NO. DESCRIPTION 4ASS Y 1 1 2 4 93310A242 3 2 ALA60061 4 1 H600131 5 1 H600200 AL600 ASSY ( in progress ) BSCS: 10-24 x 0.50 ROLLE R AL600 COVER TOP AL600 DRIVERSIDE WHEELS ASSEMBLY PARTS ITE M 2 2 14 1 10 1 2 6 4 1 19 1 9 1 18 1 20 1 7 1 8 1 11 1 1 1 6 4 12 2 16 1 17 1 3 2 21 1 5 1 13 1 15 1 18 QT Y PART NO. 5ASSY DESCRIPTION AL600 ASSEMBLY PART 5 1 1 2 6 90087A190 3 2 91251A464 SHCS: 0.
EXPLODED VIEWS 2 1 19 1 7 2 10 1 4 1 22 1 12 8 5 1 3 2 A 9 2 14 2 6 8 16 1 20 1 15 1 B 13 1 1 2 23 1 21 1 8 2 17 1 11 1 18 2 ASSEMBLY PARTS ASSEMBLY PARTS ITE M 1 QT Y 2 PART NO. 0_25-20_LOCK_NUT 90640A129 2 1 3 2 90298A534 SS:0.25 DIA,0.25 LG,10-24 TH 4 1 90298A535 SS:0.25 DIA.,0.375 LG,10-24 TH 5 1 6ASSY DESCRIPTION 90298A539 AL600 ASSEMBLY PART 6 SS:0.25 DIA.,0.
EXPLODED VIEWS 5 4 11 1 AL-600 / 650 50 AL 6 4 4 OR 6 2 10 1 7 2 3 2 8 1 00 AL 6 1 4 2 2 9 4 ASSEMBLY PARTS ITE M 5 2 4 2 AL-690 QT Y PART NO. 1 4 /6 2 2 3 2 /4 4 4/2 H600160 5 4/2 6 2/4 7 2/4 DESCRIPTION H600144 BASE LEG BRACKET HHCS 1/2-13 x 4.
