Operation Manual

T
he following keys on the RCP 4 remote may be programmed with
individual IR codes that are “learned” from another remote control:
Power On/Off, Mute, Sleep and DSP Surround/Title (Channel Up/Down),
Volume Controls, Channel Level/Disc Menu, Speaker/DVD Setup, Digital
Input/Drawer Open/Close, Delay/DVD Status,
‹›
⁄¤
Navigation, Set,
Numeric Keys, Track Skip Up/Down and Transport Controls – a total of
34 buttons.
Follow these steps to learn individual key codes:
1. Place the RCP 4 and the device’s original remote so that their IR
transmitters face each other end to end, separated by about one
inch (see Figure 3). The RCP 4 remote’s transmitter also serves as
an IR receiver during the learning process.
Figure 3 – RCP 4 and Original Remote Head-to-Head
2.
Make sure the RCP 4 is in the device mode you want to learn
the new key code for by pressing the Input Selector
, which should
light in red, or green if it is a secondary source on a dual-source
selector. If necessary, press a dual-source selector twice to select
between the primar
y and secondary sources. Place the RCP 4
remote in Learning mode by pressing and holding the Learn
Button until the Program Indicator flashes amber, then releasing
(see Figure 4).
Figure 4 – Lear
ning Remote Commands
3. Press and hold the button on the RCP 4 remote you wish to program
with the new code until the Program Indicator remains steadily lit
amber
,
then release it.
4. Press and hold the button on the device’s original remote whose
code you wish to
“lear
n”
until the RCP 4’s Program Indicator flashes
green,
then release it.
5. You may program additional buttons by repeating Steps 3 and 4.
T
o exit Lear
ning mode
, press the Learn Button once. If you prefer,
you may wait for the remote to
“time out”
and exit Lear
ning mode
on its own,
but this will take about 30 seconds
.
I
f you make a mistake while learning a code, you may either learn
a new code over the old code, or you may erase the learned code,
which returns the button to the code in the original code set that you
programmed into the Input Selector. To erase a single learned code:
1. Make sure the RCP 4 is in the device mode containing the learned
code you wish to erase by pressing the Input Selector, which should
light in red, or green if the secondary source on a dual-source
selector is active.
2. Press and hold the Learn Button until the Input Selector lights and
the Program Indicator flashes amber, then release.
3. Press the Input Selector again and release.
4. Enter the code “777” by pressing the “7” Numeric Key three times.
The Input Selector should flash each time.
5. Press the button whose learned code you wish to erase and release.
The Program Indicator will flash green to confirm the erasure.
6. Repeat Step 5 for any other buttons whose learned codes you wish
to erase.
7. Press the Learn Button to exit Learning mode, or wait about 30
seconds for Learning mode to time out.
To erase all of the learned codes for a device mode:
1. Make sure the RCP 4 is in the device mode containing the learned
code you wish to erase by pressing the Input Selector, which should
light in red, or green if the secondary source on a dual-source
selector is active.
2. Press and hold the Learn Button until the Input Selector lights and
the Program Indicator flashes amber, then release.
3. Press the Input Selector again and release.
4. Enter the code “888” by pressing the “8” Numeric Key three times.
The Input Selector should flash each time. The Program Indicator
will flash green to confirm the erasure.
To erase all of the learned codes on the remote for all device modes,
but without erasing other user settings such as product code sets or
punch-through programming
,
follow these steps:
1. Press and hold the Learn Button until the Input Selector lights in
red and the Program Indicator flashes amber, then release.
2. Press any Input Selector and release.
3. Enter the code “999” by pressing the “9” Numeric Key three times.
The Input Selector should flash each time. The Program Indicator will
go dark,
and the Input Selector you pressed in Step 2 will remain lit for
about 10 seconds
.
Then the Program Indicator will flash green to con
-
fir
m the erasure
,
and the remote will automatically exit Lear
ning mode
.
12
LEARNING INDIVIDUAL KEY CODES
12
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 12