RCP4 remote OM.
RCP4 remote OM.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 3 INTRODUCTION AND FEATURES Please register your product on our Web site at www.harmankardon.com. Note: You’ll need the product’s serial number. At the same time, you can choose to be notified about our new products and/or special promotions. WWW.HARMANKARDON.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 4 REMOTE CONTROL FUNCTIONS The RCP 4 remote is capable of controlling 11 devices, including the AVR 245 and the DVD 37 included in the CP 45 system. During the installation process, you may program the codes for each of your source components into the remote. Each time you wish to use the codes for any component, first press that component’s selector. This changes the button functions to the appropriate codes for that product.
RCP4 remote OM.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 6 REMOTE CONTROL FUNCTIONS Learn Button: The RCP 4 remote is capable of “learning” individual IR codes from the original remote that came with your TV or a device that is connected to any of the source inputs. See the Programming Sources section for instructions on learning remote codes. Channel Level/Disc Menu: Press this button to set the output levels for each channel so that all speakers sound equally loud at the listening position.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 7 REMOTE CONTROL FUNCTIONS (seeks frequencies with acceptable signal strength) Tuning modes. It also toggles between Stereo and Mono modes when an FM station is tuned. When listening to XM Radio, press the Tuning Mode Button once to view the category name of the current channel. Additional presses will display the artist, song title and channel name. When the DVD player has been selected, this button performs the Zoom function.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 8 REMOTE CONTROL FUNCTIONS NOTE: Due to the variations in how DVD discs are authored, the subtitle languages displayed by the DVD 37 may not accurately reflect the actual languages available on the disc. It is recommended that subtitles be selected using the disc’s menu. Stereo Modes/Repeat: The first press of this button will select the last-used Stereo mode, which may be Surround Off or Two-Channel Processing.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 9 BATTERIES The RCP 4 remote control uses three AAA batteries, which are included. To remove the battery cover located on the back of the remote, firmly press the ridged depression and slide the cover toward the top of the remote. Insert the batteries as shown in Figure 1, making sure to observe the correct polarity. Figure 1 – Remote Battery Compartment When using the remote, remember to point the lens toward the front panel of the AVR 245 or DVD 37.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 10 PROGRAMMING SOURCES Programming Sources The RCP 4 remote is capable of controlling not only the receiver and DVD player included in your CP system, but it may also be programmed to control many brands and models of VCRs, CD players, cable boxes, satellite receivers, cassette decks and TVs, as well as an iPod (not included) docked in Harman Kardon’s optional The Bridge. It may help to think of the remote as a book with pages.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 11 PROGRAMMING SOURCES Table 1 – Remote Control Codes Source Input Video 1 Video 2 Video 3 Video 4 HDMI 1 HDMI 2 DVD * CD Tape Product Type Remote Control Code (circle one) VCR, PVR Cable, Satellite TV TV DVD, VCR, Cable, Satellite DVD, VCR, Cable, Satellite DVD CD, CD-R Cassette * Do not reprogram the DVD Source selector unless you are replacing the DVD player included in the CP 45 system with another product. 7.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 12 LEARNING INDIVIDUAL KEY CODES The following keys on the RCP 4 remote may be programmed with individual IR codes that are “learned” from another remote control: Power On/Off, Mute, Sleep and DSP Surround/Title (Channel Up/Down), Volume Controls, Channel Level/Disc Menu, Speaker/DVD Setup, Digital Input/Drawer Open/Close, Delay/DVD Status, ‹ › ⁄¤ Navigation, Set, Numeric Keys, Track Skip Up/Down and Transport Controls – a total of 34 buttons.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 13 ADVANCED FUNCTIONS The RCP 4 remote control not only operates the AVR 245 and DVD 37, but it also serves as a universal remote that may be programmed to operate many of your other home theater components. The punchthrough and macro features add even more flexibility and versatility.
RCP4 remote OM.qxd 11/29/06 3:17 PM Page 14 ADVANCED FUNCTIONS It isn’t possible to “edit” a command within a macro. However, you may erase the macro as follows: 1. Simultaneously press and hold the Mute Button and the Macro Button containing the macro until the Program LED flashes. 2. Press the Surround Button to erase the macro.
RCP4 remote OM.qxd 11/21/06 4:12 PM Page 15 APPENDIX 2 1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 71 70 72 Refer to the numbered buttons in this drawing when using the Function List.
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 16 APPENDIX Table A1 – Remote Control Function List No.
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 17 APPENDIX No.
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 18 APPENDIX Refer to Tables A2 through A9 when programming the codes for your components into the remote.
RCP4 remote OM.
RCP4 remote OM.
RCP4 remote OM.
RCP4 remote OM.
RCP4 remote OM.
RCP4 remote OM.qxd 11/29/06 3:18 PM Page 24 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com © 2006 Harman International Industries, Incorporated. All rights reserved. Part No.
