Operation Manual

ManualsBrandsHarman Kardon ManualsAudioAVR525

PROGRAMMING THE REMOTE

PROGRAMMING THE REMOTE 39

4. Press the button on the AVR 525 remote that you

wish to program.The Program/SPL Indicator

c will stop flashing.

5.Within five seconds, press and hold the button on

the original remote that you wish to “teach” into

the AVR 525 remote.When the Program/SPL

Indicator c turns green three times, release

the button.The Program Indicator will then begin

to flash amber again.

NOTE: If the Program/SPL Indicator c turns

red during Step 5 or 6, the programming was not

successful. Repeat the steps to see whether the

code will “take.”

6. Repeat Steps 4 though 6 for each button on the

source remote that you wish to transfer to the

AVR 525 remote.

7. Once all codes have been transferred from the

original source remote to the AVR 525 remote,

press the Learn Button .

8. Repeat Steps 1 through 7 for any additional

remotes you wish to “teach” into the AVR 525

remote.

Erasing Learned Codes

The AVR 525’s remote allows you to remove or erase,

the code learned into a single button for a single device,

to remove or erase the code set for all the codes that

have been programmed into specific device buttons,or

to erase all commands that have been learned to all

devices.

To erase a single learned code from within a single

device’s settings, follow these steps:

1. Press and hold both the Input Selector ef

g within which the individual button to be erased

has been programmed and the Learn Button h.

2.When the red LED under the Input Selector turns

red and the Program/SPL Indicator c flashes

amber, release the buttons.

3. Press and release the Input Selector efg

again for the device within which the individual button

to be erased has been programmed.

4. Press the 7 Button r four times.

5. Press and release the individual button for which the

code is to be erased.The Program/SPL Indicator

c will blink green two times and then return to

amber.

6.To erase other buttons within the same device, press

them as described in Step 5.

7.When all buttons to be erased have been pressed,

press the Learn Button to complete the

process.

To erase all codes within a single device,follow these

steps:

1. Press and hold both the Input Selector

efg for which you wish to erase the codes

and the Learn Button .

2.When the red LED under the Input Selector turns

red and the Program/SPL Indicator c flashes

amber, release the buttons.

3. Press and release the Input Selector efg

again for the device whose codes you wish to erase.

4. Press the 8 button r four times.

5.The Program/SPL Indicator c will turn off and

the red light under the Input Selector will flash on

and off once to indicate that the codes have been

erased.

To erase all codes that have been programmed to all

devices in the remote,follow these steps:

1. Press any Input Selector efg for which

you wish to erase the codes and also the Learn

Button .

2.When the red LED under the Input Selector turns

red and the Program/SPL Indicator c flashes

amber, release the buttons.

3. Press and release the Input Selector efg

again for the device whose codes you wish to erase.

4. Press the 9 Button r four times.

5.The Program/SPL Indicator c will turn off and

the red light under the Input Selector will flash on

and off once to indicate that the codes have been

erased.

Macro Programming

Macros enable you to easily repeat frequently used

combinations of commands with the press of a single

button on the AVR 525’s remote control. Once pro-

grammed, a macro will send out up to 19 different

remote codes in a predetermined sequential order

enabling you to automate the process of turning on

your system, changing devices,or other common

tasks.The AVR 525’s remote can store up to five sep-

arate macro command sequences: one that is

associated with the Power On Button a and four

more that are accessed by pressing the Macro

Buttons .

1. Press the Mute Button and the Macro

Button to be programmed or the Power On

Button a at the same time.An Input Selector

will light red, and the Program/SPL Indicator

c will flash amber.

2. Enter the steps for the macro sequence by press-

ing the button for the actual command step.

Although the macro may contain up to 19 steps,

each button press,including those used to change

devices,counts as a step.The Program/SPL

Indicator c will flash green to confirm each

button press as you enter commands.

NOTE: While entering commands for Power On/Off of

any device during a macro sequence,press the Mute

Button . DO NOT press the actual Power button.

3.When all the steps have been entered, press the

Sleep Button j to enter the commands.The

red light under the Input Selectors ef will

blink and then turn off.

Example: To program the Macro 1 button so that it

turns on the AVR525,TV and a cable box, follow

these steps:

• Press the Macro 1 Button and Mute

Button at the same time and then release

them.

• Note that the Program/SPL Indicator c will

flash amber.

• Press the AVR Selector f.

• Press the Mute Button to store the

AVR 525’s power on command.

• Press the VID 2 Input Selector Button e to

indicate the next command is for “TV Power On.”

• Press the Mute Button to store the TV

Power On Command.

• Press the VID 3 Input Selector Button e to

indicate the next command is for “Cable Power On.”

• Press the Mute Button to store the Cable

Power On command.

• Press the Sleep/Channel Up Button j to

complete the process and store the macro

sequence.

After following these steps,each time you press

the Macro 1 Button , the remote will send

the Power On/Off command.