Manualshelf

Installation Sheet

ManualsBrandsHardware Resources ManualsShop AllHardware Resources 45 Pound Capacity Mixer Lift Stand with Adjustable Spring Tension and Soft Close - Platform Not Included
12
Mixer/Appliance Lift
Installation Instructions for the ML-1CH
IMPORTANT:
Before you begin, make sure you familiarize yourself with all
the parts and fully read the instructions.
CUSTOMER SERVICE:
Toll-free customer help line available weekdays between
7:00am and 6:00pm Central Time at 800-463-0660.
TOOLS NECESSARY:
Screw gun, Phillips screwdriver, level and tape measure. 10mm
and 12mm boxed end wrenches needed to make necessary
adjustment for dierent shelve weight loads. NOTE: If screw
gun has a clutch, set to lowest setting so as not to over tighten
and/or strip screws.
CABINET ADJUSTMENTS:
CABINET ADJUSTMENTS: The Mixer/Appliance Lift is designed
to install to the inside wall of any cabinet, but to insure proper
operation support material is required to be installed along
the top of both sides of a face frame cabinet with side panels
less than 3/4” thick.
STEP 1 - For Face Framed Cabinets
* Frameless Cabinets - Proceed directly to Step 2
support
material
1/2 maximum
recess
door opening
TOP VIEW
OF CABINET
SUPPORT
MATERIAL
(SUPPLIED BY
CUSTOMER)
WIDTH = 6”
LENTGH =
FULL DEPTH
OF CABINET
FRONT FACE
FRAME
FIG. A
(Support material and mounting screws not included) Install support material as high as possible on both the inside walls of the
cabinet. Support material should be 6” wide and run the entire depth of the inside of the cabinet. The thickness of the support material
should allow for a maximum ½” recess.
A Left Side Mounting Bracket 1X
B Right Side Mounting Bracket 1X
C #10 x 3/4” Pan Head Phillips Wood Screw 24X
support
material
1/2 maximum
recess
door opening
TOP VIEW
OF CABINET
SUPPORT
MATERIAL
(SUPPLIED BY
CUSTOMER)
WIDTH = 6”
LENTGH =
FULL DEPTH
OF CABINET
FRONT FACE
FRAME
FIG. A
support
material
1/2 maximum
recess
door opening
TOP VIEW
OF CABINET
SUPPORT
MATERIAL
(SUPPLIED BY
CUSTOMER)
WIDTH = 6”
LENTGH =
FULL DEPTH
OF CABINET
FRONT FACE
FRAME
FIG. A
WARNING
THIS PRODUCT IS SPRING LOADED AND COULD CAUSE SEVERE HARM IF NOT INSTALLED CORRECTLY!
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
A
B
C
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
Min.19-11/16”
Min.37-1/2”
31-1/2”
Min.15-3/4”
6-
1/4”
1-3/16”
1-3/16”
4
3
5
6
7
Switch of sensor light
1
2
3
4
5
6
7
(LED Version only)
C

Summary of content (2 pages)