Installation & Assembly

ManualsBrandsHardware House ManualsBrushed Nickel Kitchen FaucetsSingle Handle Kitchen Faucet with Side Spray

Installation Instructions

INSTALLATION INSTRUCTIONS

Before beginning

the

installation, determine your needs, and

necessary

consult

the

store where you purchased your faucet

for

valve and adapter

recommendations.

BEFORE

STARTING THE

PROJECT,

SHUT OFF HOT AND COLD WATER

SUPPLIES.

you

are

removing

existing faucet, remove

the

faucet

from

the

and clean sink thoroughly.

A: FAUCET INSTALLATION

THREE

SINK

Apply plumber's

putty

on the

bottom

the black

putty

plate. Place

the

deck plate

with

the

putty

plate onto

the

sink.

the faucet through

the

deck plate.

3. From underneath

the

sink, slide

the

mounting gasket,

the

metal mounting

washer, and then

the

seat

nut

(with

screws)

up the

hoses

to the

threaded

shank.

Thread

the nut up to the

sink.

Do not

tighten down

the

screws

until

the

faucet is properly aligned. The faucet is aligned properly when

the

spout travels

the

same distance, side

side. Once

is aligned, tighten

the

seat

nut

screws.

Remove any

excess

putty.

SINGLE

SINK

(Without

Escutcheon)

the faucet into

the

2. From underneath

the

sink, slide

the

mounting gasket,

the

metal mounting

washer, and then

the

seat

nut

(with

screws) up

the

hoses

to the

threaded

shank.

Thread

the nut

to the

sink.

Do not

tighten down

the

screws

until

the

faucet is properly aligned. The faucet is aligned properly when

the

spout travels

the

same distance, side

side. Once

is aligned, tighten

the

seat

nut

screws.

HOSE

From beneath

the

sink, connect

the

hose

to the

short outlet tube's end fitting.

Tighten

the

screw

on the

connector. Assemble

the two

halves

the balance

weight onto

the

spray hose (see picture

for

placement location). Pull spray

hose

back and

forth

check

for

smooth operation.

STEP

C: CONNECTING THE SUPPLY TUBES

The

hot

supply tube

indicated

with

red mark. Apply thread seal tape

pipe

thread compound

threads. Attach water supply lines (sold separately)

faucet lines and valves. IMPORTANT: Use

wrench

hold copper faucet

lines

place when tightening supply lines. This will help prevent twisting

and kinking. Tighten firmly (careful

not to

over-tighten) until

seal

achieved.

STEP

FLUSH

AND

CHECK FOR

LEAKS

Turn

on hot

and cold water supplies; check

for

leaks. Remove

the

pull-out spray

head

from

the

hose, Point

the

hose into

the

drain and turn

on the

faucet,

hot

and

cold mixture,

for

1 minute. Re-attach

the

spray head

hose. Run water again

and check all connection

for

leaks.

THREE

SINK

SINGLE

HOLE SINK

Escutcheon)

rosace)

FREGADERO

CON

SOLO

AGUJERO

Please

Conserve

Water!

Printed in China

Summary of content (2 pages)

PAGE 1
Installation Instructions INSTALLATION INSTRUCTIONS Before beginning the installation, determine your needs, and if necessary consult the store where you purchased your faucet for valve and adapter recommendations. THREE SINK SINGLE HOLE SINK Escutcheon) rosace) FREGADERO CON UN SOLO AGUJERO BEFORE STARTING THE PROJECT, SHUT OFF HOT AND COLD WATER SUPPLIES. If you are removing an existing faucet, remove the faucet from the and clean sink thoroughly.
PAGE 2
roller •• • adjustable ranges HOT LIMIT STOP Make sure the pressure balanced valve/ceramic cartridge is position of "off before adjusting the controller. 2. off the red thermostatic controller. 3. There eleven adjustable ranges between ) and " "(70° ).