Instructions / Assembly

ManualsBrandsHARBOR MATE ManualsAutomotive115 HP Outboard Motor Cart Engine Stand with Folding Handle

Page 1Rev. 022317

DiscountRamps.com • 1-888-651-3431

Outboard Motor Cart With Folding Handle

Instructions for Part # OMC-F315

General Guidelines

Safety Warnings

• It is the user’s responsibility to read and follow all instructions.

• Keep these instructions with the product at all times and review before each use.

• It is the responsibility of this product’s owner to furnish the instructions to any person that borrows

or purchases the product.

• Inspect the product before use to ensure it is assembled properly and all parts are in safe working

order and free of defects.

• Never modify this product in any way.

• All circumstances cannot be addressed in these instructions. Please use common sense and

practice general safety measures when using this product.

• Parts and/or instructions are subject to change without notice.

• Check that all bolts and nuts are tight before each use.

• Lubricate the wheels periodically.

• Do not overload the outboard motor cart. Only transport engines that do not exceed the weight limit

of the cart.

• Be sure to securely chock wheels for storage or while working on any engine mounted to the cart.

• When storing an engine, it is recommended to chock the wheels and position the motor facing

towards a wall with the stand handles facing outward.

• Do not leave the motor and/or motor cart unattended.

• Do not use on uneven ground. Tipping of the cart and/or motor can occur.

• Do not use the motor cart for anything other than its intended purpose.

• This motor cart is designed for moving boat engines short distances, for storage purposes, and for

use while performing motor maintenance only.

• Do not run motor while on the stand.

• Do not tow the motor cart behind any kind of vehicle.

• Keep children a safe distance away from the motor cart at all times.

• It’s highly recommended to have two people lift and position larger boat engines onto the cart for

safety.

• Do not modify the motor cart. Only use manufacturer’s replacement parts.

• Always use the motor cart on smooth surfaces.

Summary of content (4 pages)

PAGE 1
Outboard Motor Cart With Folding Handle Instructions for Part # OMC-F315 General Guidelines • It is the user’s responsibility to read and follow all instructions. • Keep these instructions with the product at all times and review before each use. • It is the responsibility of this product’s owner to furnish the instructions to any person that borrows or purchases the product. • Inspect the product before use to ensure it is assembled properly and all parts are in safe working order and free of defects.
PAGE 2
Parts A B D E M N C F O G H P Q R I S J K T L U Part Description A Caster Wheel B Quantity V W Part Description Quantity 2 M Angled Support 2 Caster Wheel Washer 2 N Handle 1 C Caster Wheel Nut 2 O M8x90 Bolt 2 D Lock Knob 2 P M8 Lock Washer 2 E Wheel 2 Q M8 Nut 2 F Engine Board 1 R M6x75 Bolt 4 G Axle Rod 1 S M6x65 Bolt 2 H Axle Washer 4 T M6x60 Bolt 2 I Axle Nut 2 U M6x35 Bolt 2 J Bottom Support 1 V M6 Lock Washer 10 K
PAGE 3
Step 2. Slide a main support tube (L) onto each end of the axle rod (G). The main supports will only fit on the axle rod with the top-end holes facing outward. Step 3. Combine the assemblies from Step 1 and Step 2 with two M6x65 bolts (S), lock washers (V), and nuts (W). The angled support tubes fit inside the main supports, under the axle rod. (3a) (2) (3b) Step 4. Place a front support tube (K) on each of the angled supports.
PAGE 4
Step 8. Secure a pneumatic wheel on each end of the axle rod. Place an axle washer (H), then a wheel (E), followed by a second axle washer, then the axle nut (I) onto the axle rod. Step 9. Thread a lock knob (D) on each side of the cart near the engine board. These knobs lock the handle in place to prevent movement. Simply loosen the knobs to fold the handle down for storage.