Instructions / Assembly

ManualsBrandsHARBOR MATE ManualsAutomotive30 HP Outboard Motor Cart Engine Stand with Folding Handle

Page 1Rev. 111319

DiscountRamps.com • 1-888-651-3431

Outboard Motor Cart

Instructions for Part # OMC-F130

General Guidelines

• It is the user’s responsibility to read and follow all instructions.

• Keep these instructions with the product at all times and review before each use.

• It is the responsibility of this product’s owner to furnish the instructions to any person that borrows

or purchases the product.

• Inspect the product before use to ensure it is assembled properly and all parts are in safe working

order and free of defects.

• Never modify this product in any way.

• All circumstances cannot be addressed in these instructions. Please use common sense and prac-

tice general safety measures when using this product.

• Parts and/or instructions are subject to change without notice.

Safety

• Check that all hardware is properly tightened before use.

• Lubricate the wheels periodically.

• Never exceed the 130 lb. weight limit.

• This carrier is designed for moving motors short distances, for storage, and while performing main-

tenance. Do not use for anything other than its intended purpose.

• Securely chock the wheels while in storage or working on a motor mounted on the motor carrier.

• When storing a motor, it is recommended to securely chock the wheels and position it against a

wall with the handle facing outward.

• Never leave a motor and/or motor carrier unattended. Do not use on uneven ground.

• Keep away from children.

• Never run the motor while on the stand.

• Never tow the carrier behind any kind of vehicle.

• When carrying any heavy motor and positioning it on the carrier, it is recommended to use two

people.

Summary of content (6 pages)

PAGE 1
Outboard Motor Cart Instructions for Part # OMC-F130 General Guidelines • It is the user’s responsibility to read and follow all instructions. • Keep these instructions with the product at all times and review before each use. • It is the responsibility of this product’s owner to furnish the instructions to any person that borrows or purchases the product. • Inspect the product before use to ensure it is assembled properly and all parts are in safe working order and free of defects.
PAGE 2
Parts A C B D E F H I G L K M N O P Q R J Part Description A Handle Tube B Quantity Part Description Quantity 1 J Turn Knob M8x40 2 Support Tube 1 K Wheel 2 C Vertical Straight Tube - 32”L 2 L Plastic Block 1 D Handle Straight Tube - 29-3/4”L 2 M M6x85 Bolt 2 E Bottom Straight Tube - 14-3/4”L 2 N M6x70 Bolt 4 F Axle 1 O M6x60 Round Head Bolt 6 G Gas Tank Strap 1 P M6x40 Round Head Bolt 4 H Foot Tube 1 Q M6 Lock Washer 16 I Plastic Foot 2
PAGE 3
Assembly Note: First, only hand-tighten parts. When assembly is complete, tighten all hardware with tools. Step 1. Connect the bottom straight tubes (E) to the axle (F) using M6x40 bolts (P), lock washers (Q), and nuts (R). (1a) (1b) Step 2. Connect the vertical straight tubes (C) to the assembly using M6x40 bolts (P), lock washers (Q), and nuts (R). Make sure the indentations on the bars are facing inward. Step 3. Slide the gas tank strap (G) onto the vertical straight tubes.
PAGE 4
Step 5. Connect the two assemblies. Fit the bolts of the foot tube assembly into the holes of the bottom straight tubes on the axle assembly. Secure in place with lock washers (Q) and nuts (R). (5a) (5b) Step 6. Connect the handle tube (A) to the handle straight tubes on the assembly. First, fit the M6x85 bolts (M) through the upper holes and secure with lock washers (Q) and nuts (R). Then fit the turn knobs (J) into the lower holes to fix the handle in the upright position.
PAGE 5
Step 8. Attach the wheels (K) to the axle. Remove the nut and one washer, slide the tire on, and replace the washer and nut. Secure with a 19mm wrench. Do not overtighten - wheels should be able to turn freely. (8a) (8b) Step 9. After assembly is complete, make sure all bolts and nuts are tightened using appropriate tools. (9) Handle: To fold down the handle, loosen the turn knobs. (10) Rev. 111319 DiscountRamps.
PAGE 6
Product Warranty and Liability GENERAL PRODUCT WARRANTY: Products purchased from the Authorized Dealer (original place of purchase) or Merchant (“Dealer”) will be free of defects in material and workmanship at the time of receipt, and will meet the specifications stated at the place of purchase transaction or online at the Dealer’s website, under normal use and service when correctly installed, operated and maintained.