Table of Contents Safetye��������������������������������������������������������� 2 Maintenancei���������������������������������������������� 10 Specifications.............................................. 5 Parts List and Diagram............................... 11 Setup........................................................... 6 Warranty.....................................................
. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. 5. Always wear eye protection. Wear ANSI-approved safety goggles. 6. Always wear hearing protection when using the tool. Prolonged exposure to high intensity noise is able to cause hearing loss. 7.
Air Source 1. Safety Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. 2.
3. WARNING: This product, when used for abrasive blasting and similar applications, produces chemicals known to the State of California to cause cancer and birth defects (or other reproductive harm). (California Health & Safety Code § 25249.5, et seq.) 5. Attach all accessories properly to the tool before connecting the air supply. A loose accessory may detach or break during operation. 6. Obey the manual for the air compressor and abrasive blaster used with this tool. 7.
Initial Tool Set Up/Installation Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Note: This air tool is shipped with a protective plug covering the inlet. Remove this plug before set up.
Air Supply Safety TO PREVENT SERIOUS INJURY FROM EXPLOSION: Use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. NOTE: A DRY, OIL-FREE AIR SUPPLY IS CRITICAL. Moist or lubricated air will quickly clog the blaster and render it unusable. 2. Attach an air hose to the compressor's air outlet. Connect the air hose to the air inlet of the tool.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired.
General Operating Instructions 3. Open the Air Valve. 4. Open the Throttle Valve about halfway for now. This may require adjustment later for optimal performance. 5. Slowly open the Abrasive Valve completely. 6. Direct the Nozzle at the work surface and open the Trigger Valve to start blasting. Note: Media flow will be intermittent at first. 7. As needed, adjust the Throttle Valve to optimize operation. 8. If media clumps and flow stops: a.
User‑Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. Safety TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Close all valves, detach the air supply, and pull on the safety valve to release all residual air pressure before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.
Parts List and Diagram THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
