SPECIFICATIONS TABLE Sizes Inner Diameter Outer Diameter Length Receiving Cup 1-3/4″ 1-13/16″ 2-1/8″ 2-1/4″ 1/2″ 7/16″ 1-3/4″ 2″ 2-3/8″ 1-3/4″ 2″ 3″ 3/4″ 2″ 2-1/4″ 1-7/16″ 2-1/4″ 2-1/2″ 1″ 2″ 1-1/2″ 2-1/4″ 2-1/4″ 2-3/4″ 2-7/16″ 2-5/8″ 2-3/16″ 2-1/2″ 2-1/2″ 3″ 2-3/4″ 2-7/8″ 2-7/16″ 3/4″ 2-3/4″ 2-1/4″ 2-1/4″ 2-7/8″ 3-3/16″ Installing Tube Remover / Installer Receiving Tube Applications Material Most GM®, Ford®, and Dodge® 2 & 4 WD Pickups, Vans, and SUV’s through 1997 Forged, heat treat
job better and safer at the rate for which it was designed. on how to safely secure the vehicle in place with jacks, stands, etc. 8. Store this product out of the reach of children and do not allow people unfamiliar with the product or these instructions to operate the product. This product could be dangerous in the hands of untrained users. 14. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
. To do so, unscrew and remove the Forcing Screw, Steel Ball, and O-Ring from the C-Frame. 5. Make sure Steel Ball and O-Ring remain inside the Forcing Screw. Then insert Plug Bolt into Forcing Screw. 6. Screw threaded end of Forcing Screw, with its Steel Ball, O-Ring, and attached Plug Bolt back into threaded end of C-Frame toward unthreaded hole of C-Frame. Removing a Ball Joint 1.
Installing a Ball Joint 1. Mount Remover/Installer (13) on Forcing Screw assembly so that the larger diameter portion of Remover/ Installer faces the threaded hole of C-Frame and smaller diameter portion faces the unthreaded side of ball joint. 2. Place mounted Remover/Installer on unthreaded side of ball joint. 3. Align mounted Remover/ Installer, ball joint, and proper size Receiver Tube (1-6, 10-11) to allow installation of ball joint. 4.
BALL JOINT ADAPTER APPLICATIONS U = Upper, L = Lower, R = Remove, I = Install Upper/ Lower Vehicle Part Numbers Below Illustrated on Page 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FORD® L 1986-97 Aerostar® I U 1987-88 2WD Bronco II® I U 1989-90 2WD Bronco II® I L 1989-90 2WD Bronco II® I U 1991-94 2WD Explorer® I L 1991-94 2WD Explorer® I U 1983-88 2WD Ranger® I U 1989-97 2WD Ranger® I I U 1987-96 2WD 1/2-Ton Pickup I I L 1997 2WD & 4WD1/2Ton Pickup U 1987-97 2WD 3/4-
BALL JOINT ADAPTER APPLICATIONS U = Upper, L = Lower, R = Remove, I = Install Upper/ Lower Vehicle Part Numbers Below Illustrated on Page 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 FORD® (CONTINUED) L 1992-97 2WD 1/2-Ton Van L 1992-97 2WD 3/4-, 1-Ton Van L 1984-89 4WD Bronco II® I L 1990 4WD Bronco II® with Dana 28 I LU 1990 4WD Bronco II® with Dana 35 I U 1991-93 4WD Explorer® with Dana 35 I U 1990-93 4WD Ranger® with Dana 35 I U 1992-97 4WD 1-Ton I I R U 1980-96 4WD 1/2-,3/4
BALL JOINT ADAPTER APPLICATIONS U = Upper, L = Lower, R = Remove, I = Install Upper/ Lower Vehicle Part Numbers Below Illustrated on Page 10 1 2 3 4 5 6 7 8 9 10 11 12 13 14 DODGE® / CHRYSLER® / PLYMOUTH® L L L L L L L U L U L U L LU L U 1987-97 2WD Dakota ® 1972-93 1/2-, 3/4-Ton 2WD Pickup 1974-93 1/2-Ton 2WD ® Ramcharger 1979-97 1/2-, 3/4-, 1-Ton 2WD Van 1972-93 2WD 3/4-, 1-Ton Pickup RI I R RI I R RI I R RI I R 1979-97 1-Ton 2WD Van I R I R ® 1984-96 Caravan , Voy‑ ® ®
BALL JOINT ADAPTER APPLICATIONS U = Upper, L = Lower, R = Remove, I = Install Upper/ Lower Vehicle GENERAL L Part Numbers Below Illustrated on Page 10 1 2 3 4 5 6 7 8 I R 1982-97 2WD S-10 Blazer®, Jimmy, Pickup L 1985-97 Astro Safari® Van I L 1973-95 2WD 1/2-, 3/4Ton G Van I L 1996-97 4WD 1/2-, 3/4-, 1-Ton R I JEEP® 1 2 LU LU U U L L L U L L L LU LU 1993-97 2WD Grand ® Cherokee 1993-95 4WD Grand ® Cherokee , Grand Wag‑ ® oneer 1987-97 4WD Wrangler ® ® 1984-95 4WD Cherokee , ®
Parts List and Diagram Part Description Qty Part Description Qty 1 Receiving Tube 1 9 Installing Tube 1 2 Receiving Tube 1 10 Receiving Tube 1 3 Receiving Tube 1 11 Receiving Tube 1 4 Receiving Tube 1 12 Receiving Cup 1 5 Receiving Tube 1 13 Remover / Installer 1 6 Receiving Tube 1 14 Plug Bolt 1 7 Receiving Cup 1 15 Carrying Case 1 8 Installing Tube 1 4 5 3 9 8 10 1 2 11 15 14 7 13 6 12 PLEASE READ THE FOLLOWING CAREFULLY NEITHER THE MANUFACTURER
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 Page 12 For technical questions, please call 1-800-444-3353.
