Specifications Maximum Capacity 900 lb. for Single Stage; 750 lb. for Two Stage (Combined) Scaffold Stackable Up To Two Levels Only Adjustable Mounting Holes 1/2″ Diameter (30 Per Side) Platform Height 28″ to 71-1/8″ High, Single Stage NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.
4. Before using, check all parts for proper function and damage; do not use if damaged or functioning improperly. Do not straighten deformed parts. 5. Immediately remove Scaffold from service and destroy if exposed to excessive heat, such as fire, due to loss of structural strength. 6. Do not allow objects or slippery material to accumulate on Scaffold. 7. Do not use with damaged or deteriorated deck. Periodically coat wood decking and rails with transparent (penetrating) wood preservative.
26. Only use the included platform or an identical replacement platform. The platform must not extend beyond the base support. 27. Maintain labels and nameplates on the Scaffold. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 28. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
Figure 2 Assembly TO PREVENT SERIOUS INJURY: Scaffold components from other manufacturers must not be used with this Scaffold. Safety equipment added to this Scaffold, such as rails, toe guards, stability strapping, and safety harnesses, must be installed by a qualified technician. They must fit together without being forced, and the Scaffold’s structural integrity must be maintained. Figure 1 Locking Pin (5) Side Rail (1) Height Adjustment Pin (7) Locking Pin (5) & Pin Spring (6) 2.
Figure 4 Bolt (9) Nut (10) 5. Use the four Bolts (9) and Nuts (10) additionally to secure the Wooden Platform in place. 6. Guard rail holders are built into the scaffold as noted in Figure 3. Guard rails (sold separately) must be installed by a qualified technician. They must fit properly into the scaffold’s holders and must be secured in place. 7. The second stage (if needed) must be assembled by using the first stage as a stable platform from which to perform the assembly.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. General Operating Instructions TO PREVENT SERIOUS INJURY: Inspect scaffolds thoroughly before use each day. Check all components and Locking Pins before each use. Do not use front-end loaders, forklifts or similar pieces of equipment to support scaffold platforms.
Attaching A Second Stage Attach Second Stage End Frames to Stable Structure Here TO PREVENT SERIOUS INJURY: Before assembling the second stage, the lower stage must be completely assembled even if it is not being used. The lower stage provides needed structural support for the upper stage. Observe all safety rules for boarding, working on, and getting off the first stage when assembling. Assemble the upper stage one piece at a time to help prevent clutter and falling parts.
Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. Only a qualified technician may replace any parts or make any safety equipment additions to this Scaffold. 1. Periodically coat wood decking and rails with transparent (penetrating) wood preservative. DO NOT PAINT OR USE OPAQUE SURFACE SEALANTS, THEY MAY CONCEAL SERIOUS PROBLEMS. 2. BEFORE EACH USE, inspect the general condition of the Scaffold.
Parts List And Assembly Diagram Part 1 2 3 4 5 6 7 8 9 10 Description Qty Side Rail End Frame Reinforced Wooden Platform Swivel Caster Locking Pin Pin Spring Height Adjustment Pin Platform Hold Down Bolt (not shown) Nut (not shown) 2 2 1 4 8 8 4 2 4 4 1 3 8 5 6 7 5 2 6 4 Page 10 For technical questions, please call 1-888-866-5797.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
