Table of Contents SAFETy Safety ......................................................... 2 Specifications ............................................. 5 Setup .......................................................... 5 Operation .................................................... 6 Maintenance ............................................... 8 Parts List and Diagram .............................. 10 Warranty ....................................................
0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating.
Grinder Safety Warnings For your Own Safety Read Instruction Manual Before Operating Grinder 1. Wear eye protection. SAFETy 2. Use grinding wheel suitable for speed of grinder. 3. Replace cracked wheel immediately. 4. Always use guards. Only plug in sharpener when fully assembled. 5. Be careful of bits when sharpening. Bits will become hot. Handle with care; allow tips to cool before storing. 6. Housing may become hot while using. This is a normal result of operation. SETUp 7.
. Grip workpiece as lightly as possible (while still keeping safe control of it). Let the tool do the work. 6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAFETy SAVE THESE INSTRUCTIONS. Specifications Electrical Rating 120VAC / 60Hz / 0.
Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETy TO pREVENT SERIOUS INJURy: DO NOT OpERATE WITH ANy GUARD DISABLED, DAMAGED, OR REMOVED. Workpiece and Work Area Set Up SETUp 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 3.
properly Sharpened Bits Center point Cutting Edge Bit is properly sharpened when it has the following characteristics. SAFETy 1. A sharp point in the center of the bit. 2. Two sharp and equal cutting edges. Trailing Edge 3. Two trailing edges that are slightly lower than the cutting edges. MAINTENANCE OpERATION SETUp Figure C: parts of the Bit Item 61778 For technical questions, please call 1-888-866-5797.
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETy TO pREVENT SERIOUS INJURy FROM ACCIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO pREVENT SERIOUS INJURy FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Troubleshooting Tool operates slowly. Performance decreases over time. 3. Tool’s thermal reset breaker tripped (if equipped). 4. Internal damage or wear. (Carbon brushes or switch, for example.) Extension cord too long or wire size too small. 1. Accessory dull or damaged. 2. Carbon brushes worn or damaged. Excessive noise Internal damage or wear. (Carbon or rattling. brushes or bearings, for example.) Overheating. 1. Forcing machine to work too fast. 2. Accessory dull or damaged. 3.
parts List and Diagram pLEASE READ THE FOLLOWING CAREFULLy SAFETy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Assembly Diagram SAFETy 1 2 3 4 5 6 7 8 SETUp 9 10 11 12 13 14 16 15 OpERATION 17 18 19 20 21 33 22 23 27 25 32 MAINTENANCE 24 26 28 29 30 31 Item 61778 For technical questions, please call 1-888-866-5797.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
