DUAL DRUM Rotary Rock tumbler Model 67632 Set up and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
NOTICE is used to address practices not related to personal injury. Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 100’ 150’ 0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. TABLE A 7. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw.
2. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician. 8. The outlet must be properly installed and grounded in accordance with all codes and ordinances. 3. Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor.
to heart pacemaker could cause pacemaker interference or pacemaker failure. 13. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the State of California] to cause cancer, birth defects or other reproductive harm.
TO PREVENT SERIOUS INJURY: Do not operate with ANY guard disabled, damaged, or removed. Moving guards must move freely and close instantly. this is a constant process, it does not however, naturally polish the rocks. The Tumbler uses an abrasive media instead of sand. It is graded by grain size, from fine powder sized grains, up to large sized grains.
5. Make sure that the Stops (6) are lightly touching each Barrel Lid (9). This will prevent the Barrel Lids from rubbing against the housing and will reduce friction. 6. To open either Rubber Barrel, remove the Barrels from the unit and then remove the Knurled Nuts (7) and the Washers (8). Next, remove the Barrel Lids (9). 7. 8. 9. Note: It is imperative to load the Tumbler with the proper amount of materials, or the process will not be successful, and the motor could be damaged.
First Grind, Pre-Polish, Polish and Burnishing First Grind: Run the Tumbler for 24 hours, checking for gas build-up at the first twelve hours. Slowly open the Barrel Lid, releasing the small amount of gas that builds up during the process. Check the stones, they should show slightly rounded edges. Clean the seals and close the Lids. It is important to release the gas, otherwise it will thicken the abrasive slurry. After another 24 hours check again. If the slurry is thickening, add a little water.
Notes to remember: 1. Always clean Barrels and stones between steps. 2. When polishing or burnishing use plastic pellets (they will wear out during use). 3. Use a log book to keep track of each step. 4. If starting with stream-worn or smooth stones, you may be able to eliminate the first step. 5. Purchase a mineral book which details selection of stones for tumbling. As you learn about relative hardness of each stone you will achieve greater success by not mixing soft and hard stones. 6.
PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.
ASSEMBLY DIAGRAM Please note: Not all parts are washable. Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 67632 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
