8V Cordless Drill 68239 18V Cordless Drill Read this material before using this product. Failure to do so can result in serious injury. Save this manual. When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-800-444-3353 as soon as possible. Visit our website at: http://www.harborfreight.com Copyright© 2010 by Harbor Freight Tools®. All rights reserved.
Specifications Charger Input 120 V~ / 60 Hz Motor Speed 0-900 RPM Chuck 3/8”, Keyless Settings 20 Torque Settings 1 Drill Setting Max. Torque 7 ft.-lbs. DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
. Personal safety a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. b. Use personal protective equipment. Always wear eye protection.
2. Let bit cool before touching, changing or adjusting it. Bits heat up dramatically while in use, and can burn you. 3. If the drill bit jams, release the trigger immediately; drill torque can cause injury or break bit. 4. Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 5. Avoid unintentional starting. Prepare to begin work before turning on the tool. 6.
7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately. SAVE THESE INSTRUCTIONS. Extension Cords Note: Extension cords must not be used with this item’s charger. Symbology Double Insulated Grounding Canadian Standards Association TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Instructions for Putting into Use Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Unlock and release the Trigger and disconnect Battery Pack before assembling or making any adjustments to the tool. Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Assembly Diagram on page 1011.
9. Store the Charger and Battery Pack indoors, out of reach of children. WARNING! Do NOT use a different Charger or Battery to power this Drill. Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Unlock and release the Trigger and disconnect Battery Pack before adjusting tool or installing accessories.
b. Use the torque setting (marked by the drill icon) for drilling. • It is recommended that a very low torque setting be used when first driving small screws into soft materials. Then adjust the setting as the proper force required is determined. 10. Clean then store the Drill indoors and out of children’s reach. Maintenance and Servicing • The torque setting required depends on the item being driven. In the case of screws, consider the size, length, and type of material.
Troubleshooting Problem Tool will not start. Possible Causes 1. No power at outlet during charging. 2. Internal damage or wear. (Carbon brushes or switch, for example.) Performance 1. Accessory dull or damaged. decreases over time. 2. Carbon brushes worn or damaged. Excessive noise Internal damage or wear. (Carbon or rattling. brushes or bearings, for example.) Overheating. 1. Forcing tool to work too fast. 2. Accessory misaligned. 3. Accessory dull or damaged. 4. Blocked motor housing vents.
Parts List and Assembly Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Parts List and Assembly Diagram Assembly Diagram 2 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 68239 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
