Table of Contents Safetye��������������������������������������������������������� 3 Specifications.............................................. 6 Setup........................................................... 7 Operationa��������������������������������������������������� 12 Maintenancei���������������������������������������������� 13 Parts List and Diagram............................... 14 Warranty.....................................................
IMPORTANT SAFETY INFORMATION General Tool Safety Warnings Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. 1. KEEP GUARDS IN PLACE and in working order. 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 3. KEEP WORK AREA CLEAN.
Grounding Instructions TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION READ AND FOLLOW THESE INSTRUCTIONS: 110-120 V~ Grounded Tools: Tools with Three Prong Plugs 1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug.
Dust Reclaimer Safety Warnings For Your Own Safety Read Instruction Manual Before Operating 1. Wear eye protection. 2. Do not use with any openings blocked. Keep openings clear of anything that may limit air flow or hinder motor operation. 3. Do not use the Reclaimer without its Filter (18) in place. Before each use, make sure the Filter is not clogged. 4. This product is designed only to pick up dry debris.
Specifications Page 6 Electrical Rating 120V~ / 60Hz / 12A Motor No Load Speed 18,900 RPM Product Compatibility For use with Item 60738 Industrial Blast Cabinet Capacity Approximately 1-3/4 Gallons Hose Size 2″ Diameter x 3 Ft. Long For technical questions, please call 1-800-444-3353.
Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.
4. Use the pattern in Figure C as a reference, or hold the assembled Dust Reclaimer against the wall where you intend to mount it, and mark the drill hole positions through the mounting holes. 5. Drill holes in the wall to except the Wall Anchors (33). Use a concrete drill bit that is 5/16″ diameter. CAUTION! When mounting the Dust Reclaimer to a wall surface, make sure that the wall and the mounting hardware used are capable of supporting the weight of the Dust Reclaimer and its contents.
6. Tap the Wall Anchors (33) into the wall using a hammer. They will expand inside the wall when you thread a nut onto them. See Figure D below. 7. Attach the dust reclaimer to the wall using Washers (35), Spring Washers (36) and Nuts (46). See Figure E below. wal l Wall Anchor (33) Washer (35) Figure D Spring Washer (36) Nut (34) Figure E 8. Attach the blast cabinet to the Dust Reclaimer as shown in Figure F, then firmly tighten up the Hose Clamps (15).
How To Install The Dust Reclaimer To A Blast Cabinet (60738) 1. Open the right side door of the blast cabinet. Remove the four screws on the exhaust board. Take out the Exhaust Board (see Figure G). 4. Assemble the two Support Brackets (32) to the Housing (22A) using Bolts (28), Spring Washers (29), Washers (30), and Nuts (31). Do not tighten the Nuts (31) completely at this point. See Figure I. 5. Place the Support Brackets (32) on a flat surface.
7. There will be bolts and nuts already in the holes where the Dust Reclaimer will be attached to the Blast Cabinet. Remove the bolts and nuts. See Figure J. 8. Attach the Dust Reclaimer to Blast Cabinet using the Bolts (51), Flat Washers (44), Spring Washers (45) and Nuts (46). Parts 45 and 48 attach to the bolts from inside the cabinet. See Figure K. Figure J Hose Connector (48) Hose (16A) Hose Clamp (15) Hose Clamp (15) Figure K Item 60739 For technical questions, please call 1-800-444-3353.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. PREVENT SERIOUS INJURY: DO NOT OPERATE WITH ANY GUARD DISABLED, DAMAGED, OR REMOVED. 1.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any procedure in this section. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. 1.
Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Assembly Diagram 46 45 12 51 44 25 8 14 13 25 48 47 2 6 1 3 4 5 7 11 10 9 15 16A 8 16B 22 15 27 27 27 17 8 28 29 30 30 31 23 24 26 18 19 20 21 32 35 36 34 33 wall Page 15 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
