Table of Contents Safety.......................................................... 2 Maintenance............................................... 12 Specifications.............................................. 6 Parts List and Assembly Diagram.............. 15 Setup........................................................... 7 Warranty..................................................... 16 Safety Operation....................................................
1. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of injury to persons. 4. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations. 5. Use safety equipment.
Air Source 1. Safety Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. 2.
Silicosis and Aluminum Oxide Warnings NIOSH recommends the following measures to reduce crystalline silica exposures in the workplace and prevent silicosis and silicosis-related deaths: 1. Prohibit silica sand (or other substances containing more than 1% crystalline silica) as an abrasive blasting material and substitute less hazardous materials. 2. Conduct air monitoring to measure worker exposures. 4. Practice good personal hygiene to avoid unnecessary exposure to silica dust. 5.
Functional Description Specifications Safety Maximum Air Pressure 65 PSI Hose Inlet (to air source) Hose Outlet (to gun) 1/4″ -18 NPT 1/8" Gun Inlet 1/8″ Abrasive Type Powder Maximum Particle Size* 0.50 mm Cup Capacity 0.5 Ounces Hose 5' L x 5/32" ID *Note: Nozzle is very small and can clog if grit abrasive particle size is too large.
Initial Tool Set Up/Assembly Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Note: This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up. Mounting the Hanger 1. Choose a mounting location that is free of electrical wiring or other obstructions, and is sturdy enough to support the weight of the tool. 3. Drill holes at the marked locations. 4.
Description Non-lubricated Tools A Air Hose Filter Regulator Lubricator (optional) Coupler and Plug Leader Hose (optional) Air Cleaner / Dryer (optional) Air Adjusting Valve (optional) Maintenance A B C D E F G H Operation Lubricated Tools B B C C A A E E F H Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging w
Item 69277 For technical questions, please call 1-800-444-3353.
Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use the tool until repaired.
2. Connect the tool’s Air Hose & Filter Assembly to the air supply source. Set the compressor’s regulator to no more than 65 PSI. Do not exceed 65 PSI. IMPORTANT: Practice using the Air Eraser on scrap material to become accustomed to how the tool operates. 3. Hold the Air Eraser as you would a pencil. 4. To release abrasive, press the Control Button and hold it down. Move the Air Eraser with the Nozzle about 1/8" to 1/2" above the work surface. 5.
User‑Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. Safety To prevent serious injury from accidental operation: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the Control Button before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment.
Troubleshooting 1. Adjustment Screw not properly adjusted. 2. Abrasive level too low. 3. Nozzle too close to or too far from the workpiece surface. Decreased output. 1. Not enough air pressure and/ or air flow. Likely Solutions 1. Re-adjust Adjustment Screw. 2. Refill Cup. 3. Keep Nozzle 1/8" to 1/2" from the workpiece surface. 1. Check for loose connections and make sure that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool's air inlet.
PLEASE READ THE FOLLOWING CAREFULLY Safety The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.
Parts List and Assembly Diagram 1 2 3 4 Description Air Eraser Body Air Hose Hanger 150g XXX Grit (or mesh) Abrasive Media 3 Qty Part 1 1 1 1 5 6 7 8 8 Description Comfort Face Mask* Cup Cup Lid Adjustment Screw Qty 1 1 1 1 Safety Part 2 1 7 Setup 6 5 Operation 4 Maintenance * Included face mask is intended to increase comfort only and is not designed to provide protection from hazardous airborne particles Record Product's Serial Number Here: Note: If product has no serial number, r
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
