electric Meat grinder 99598 HEAVY-DUTY electric Meat grinder 99599 Cleaning, Assembly, And Operation Instructions Model 99598 Model 99599 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
IMPORTANT SAFEGUARDS 1. When using electrical appliances, basic safety precautions should always be followed, including the following: 2. Read all instructions. 3. To protect against risk of electrical shock, do not put Motor, Fan, or Gearbox in water or other liquid. 4. Close supervision is necessary when any appliance is used by or near children. 5. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning. 6. Avoid contacting moving parts.
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. Electrical Safety 1. To protect against electrical shock do not immerse cord, plugs, or the main unit in water or other liquid. Only the removable non-electrical parts of the unit may be immersed for cleaning. Thoroughly clean and dry these parts prior to first use and before every subsequent use. 2. This appliance has a polarized plug (one blade is wider than the other).
2. 3. Provide adequate ventilation space on all sides of the appliance, especially near vents. Inadequate ventilation may cause fire or damage to the appliance. Keep multiple ABC class fire extinguishers nearby. Monitor the appliance while in use. Foodborne Illness Safety 1. 2. Before every use, thoroughly clean the appliance (see “Cleaning” section for instructions) EXCEPT for thoseparts that do not touch foods. Then wash your hands.
13. This product is not a toy. Keep it out of reach of children when children are not being closely supervised. 14. WARNING: Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) 15. When carrying Meat Grinder, hold Motor Housing with both hands. Do not carry by holding Hopper Plate. 16.
ed) to Cutting Plates to keep them lubricated. Unpacking When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Cleaning Read the entire Important Safeguards section at the beginning of this manual including all text under subheadings therein before set up or use of this product. 1. 2. 3. 4. 5.
4. Slide Cutting Blade (9) onto Feed Screw, making sure the edges of Cutting Blade face front of housing. 4. To make sausage, insert desired Sausage Maker (3, 4, or 5) into Sausage Adapter (2). 5. WARNING! Cutting Blade has sharp blades. Wear gloves and use care when installing Cutting Blade. 5. Place wide end of Sausage Adapter against the Head and in front of Cutting Blade. 6. Slide selected Cutting Plate (6, 7, or 8) over Cutting Blade, using the slot along Plate edge as guide. 6. 7.
Note: For additional information regarding the parts listed in the following pages, refer to the 99599 Assembly Diagram on pages 12 and 13 of this manual. 1. Slide Head (12) into Housing Opening (15). While holding Head, place Locking Knob (16) into slot on Left side of Motor Housing (17). 2. Turn Locking Knob clockwise until tight and Head fastened securing to housing. 3. 4. 5. 6.
. To prevent serious injury from Appliance failure: Do not use damaged appliances. If abnormal noise or vibration occurs, have the problem corrected before further use. If the Grinder gets jammed, the overload light will flash and the beep-beep alarm will sound. 10. When jammed, the Circuit Breaker (26) will trigger. Once jam is cleared (Inspection And Maintenance), reset Circuit Breaker switch. 11. To make sausage, insert desired Sausage Maker (3, 4, or 5) into Sausage Adapter (2). 1.
99598 PARTS LIST Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25.
99598 ASSEMBLY DIAGRAM SKU 99598/99599 For technical questions, please call 1-800-444-3353.
99599 PARTS LIST Part 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38.
99599 ASSEMBLY DIAGRAM SKU 99598/99599 For technical questions, please call 1-800-444-3353.
