WELDING TORCH MINI-KIT Model 95671 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright© 2007 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
PRODUCT SPECIFICATIONS Item Product Applications Required Gas Pressure Hose Assembly Additional Features Accessories Weight Description Used for jewelry, hobby crafts, metal sculptures, electronics, etc. Can be used with acetylene, hydrogen, propane, or natural gas. 0.2mm Tip = 2 PSI Oxygen / 2 PSI Fuel 0.3mm Tip = 3 PSI Oxygen / 3 PSI Fuel 0.4mm Tip = 4 PSI Oxygen / 4 PSI Fuel 0.5mm Tip = 6 PSI Oxygen / 5 PSI Fuel 0.6mm Tip = 6 PSI Oxygen / 6 PSI Fuel 6 Ft.
. Keep bystanders, children, and visitors away while operating welding equipment. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. Children should not be allowed in the work area. PERSONAL SAFETY 4. Stay alert. Watch what you are doing, and use common sense when operating welding equipment. Do not use welding equipment while tired or under the influence of drugs, alcohol, or medication.
SERVICE 13. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. 14. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1.
structure, as in walls or ceilings, without an approved method for eliminating the hazard. Do not dispose of hot slag in containers holding combustible materials. Keep a fire extinguisher nearby and know how to use it. After welding or cutting, make a thorough examination for evidence of fire. Be aware that easily visible smoke or flame may not be present for some time after the fire has started. Do not weld or cut in atmospheres containing dangerously reactive or flammable gases, vapors, liquids, and dust.
. Always keep the Welding Hoses (7, 8) away from moving parts on the tool. Examine the Welding Hoses for cuts, burns, or worn areas before each use. If any damaged areas are found, replace the Welding Hoses immediately. 7. Read and understand all instructions and safety precautions as outlined in the manufacturer’s manual for the material you will weld or cut. 8. Proper cylinder care. Secure cylinders to a cart, wall, or post, to prevent them from falling.
chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code 25249.5 et seq.) UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 11 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.
5. IMPORTANT! The Pressure Adjusting Screw on the Acetylene Regulator (not included) and the Pressure Adjusting Screw on the Oxygen Regulator (not included) should be opened slightly by turning counterclockwise to relieve pressure on the regulator diaphragms before opening the cylinder valves. If this is not done, pressure from the cylinders may damage the diaphragms and render the regulators inoperable. (See Figure B.
8. Depending on use, attach a Tip (1, 12, 13, 14, 15) to the Mixer (2) on the Torch Handle (5). (See Figure B.) 9. Open the Oxygen Valve Stem (9) on the Torch Handle (5). Adjust the Oxygen Regulator to the desired working pressure. Then, close the Oxygen Valve Stem on the Torch Handle. (See Figure B.) 10. Open the Acetylene Valve Stem (10) on the Torch Handle. Adjust the Acetylene Regulator to the desired working pressure. Then, close the Acetylene Valve Stem on the Torch Handle. (See Figure B.) 11.
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure the Welding Torch Mini-Kit is cool to the touch and disconnected from its oxygen and acetylene cylinders before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the Welding Torch Mini-Kit. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged Welding Hoses (7, 8), and any other condition that may affect its safe operation.
12 SKU 95671 For technical questions, please call 1-800-444-3353 14 15 Part # 1 2 3 4 5 6 7 8 Description Welding Tip (0.2mm) Mixer Body Inner Tube Handle Retainer Hose (Green) Hose (Red) Qty. 1 1 1 2 1 1 1 1 Part # 9 10 11 12 13 14 15 Description Valve Stem Assy. (Oxygen) Valve Stem Assy. (Acetylene) Retainer Tip (0.3mm) Tip (0.4mm) Tip (0.5mm) Tip (0.6mm) NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 13 Qty.
