3/8” DRILL DRIVER KIT 14.4 VOLT 95094 OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com To prevent serious injury, Read and understand all warnings and instructions before use. Copyright© 2006 by Harbor Freight Tools®. All rights reserved.
Product Specifications Power Source 14.4 VDC NiCd Battery Charge Time 3 to 5 Hours Charger Input/Output 120 VAC / 60 Hz; 15 VDC - 400 mA Chuck Type 3 Speed 550 RPM Torque Settings 20 Reversible Yes Weight 3.45 Pounds /8” Keyless Save This Manual You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual.
grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 2. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way.
Tool Use and Care 1. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 3. Do not use the power tool if the trigger does not operate it.
Specific Safety Rules 1. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use the Cordless Drill in areas near flammable chemicals, dusts, and vapors. Do not use this product in a damp or wet location. 2. Maintain labels and nameplates on the Cordless Drill. These carry important information.
these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.
3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE B FIGURE A Double Insulated Tools: Tools With Two Prong Plugs 1. Tools marked “Double Insulated” do not require grounding.
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. . Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.
UNPACKING When unpacking, check to make sure that the product is complete and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. Charging 1. NOTE: The Battery Pack (23) requires charging. The first charge requires 5 hours charge time prior to using the Cordless Drill. 2. Note: Always switch to a fresh battery when tool performance begins to diminish.
OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 14. 1. WARNING! Remove the Battery (23) from the tool and set the Locking Lever (7) to its center, locked position before making any adjustments, changing accessories, or storing the tool. CHUCK (1) LOCKING LEVER (7) TORQUE SETTING RING (3) TRIGGER (10) BATTERY PACK (23) BATTERY BUTTON LOCK (26) FIGURE E 2.
Drill Setting ( ): This setting essentially prevents the clutch from slipping entirely. It is designed for drilling, but is not advised for using the screwdriver because it offers no protection against stripping the head or splitting the wood. Set the driving torque by turning the Torque Setting Ring (3) to align the torque indicator arrow with the desired setting. (See Figure E, previous page.) 5.
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Remove the Battery (23) from the tool and set the Locking Lever (26) to its center, locked position before performing any inspection, maintenance, or cleaning. 2. BEFORE EACH USE, inspect the general condition of the Cordless Drill. Check for misalignment or binding of moving parts, cracked or broken parts, leaking Battery Pack, damaged Charger wiring, chipped or broken Drill Bits, and any other condition that may affect its safe operation.
PARTS LIST Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Description Chuck Plate Torque Setting Ring Radiator Upper Orientation Block Lower Orientation Block Locking Lever Orienting Plate Spring Trigger Bushing Steel Ball Battery Terminal Clamp Gear Housing Left Housing Motor Support Screw Drive Gear Motor Right Housing Charger AC/DC Adapter Battery Pack Q’ty 1 1 1 1 1 1 1 1 1 1 1 13 1 1 1 1 3 1 1 1 1 1 1 Part 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Descri
ASSEMBLY DIAGRAM 23- Battery Pack Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 95094 For technical questions, please call 1-800-444-3353.
