OSCILLATING SPINDLE SANDER 95088 Assembly And Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2006 by Harbor Freight Tools®. All rights reserved.
PRODUCT SPECIFICATIONS Electrical Requirements Speed Oscillating Range Dust Port Construction Table Size Overall Dimensions 120 VAC, 60 Hz, 3.5 Amps 2,000 RPM, 5/8” Stroke 58 OPM 1-1/2” OD 100% sealed ball bearing construction 14-11/32” L x 11-15/32” W 15-9/16” L x 14-1/8” W x 17” H Spindle Dimensions 1/2” x 1.5 mm thread Tool Weight 33 Lb.
ELECTRICAL SAFETY 4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user. 5.
14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations. 15. Use safety equipment. Always wear eye protection. Dust mask, nonskid safety shoes, hard hat, or hearing protection must be used for appropriate conditions. Always wear ANSI approved safety goggles and a dust mask/respirator when using or performing maintenance on this tool. TOOL USE AND CARE 16.
of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RULES 1. Maintain labels and nameplates on the Sander. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Avoid unintentional starting. Make sure you are prepared to begin work before plugging in the Sander. 3. WARNING! People with pacemakers should consult their physician(s) before using this product.
on variations in local line voltage. Extension cord usage may also affect tool performance. GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged.
Double Insulated Tools: Tools With Two Prong Plugs 1. Tools marked “Double Insulated” do not require grounding. They have a special double insulation system which satisfies OSHA requirements and complies with the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard Association, and the National Electrical Code. (See Figure B.) 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Figure B.) Extension Cords 1.
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 or 240 VOLT) NAMEPLATE AMPERES EXTENSION CORD LENGTH (at full load) 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - FIGURE C * Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
UNPACKING When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. INSTALLING AND CHANGING SANDING SLEEVES WARNING! Always make sure the Power Cord (73) of the Spindle Sander is unplugged from its electrical outlet prior to making any adjustments to the tool. 1.
OPERATION NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on pages 11 through 14. 1. After you have put on the appropriate safety gear covered on page 3 of this manual, and you have installed the sanding sleeve you want to use, plug in the Sander. 2. Turn the sander on using the Switch (80). Always run the Sander for a few seconds before contacting the work piece. 3. Contact the work piece with minimal pressure.
PARTS LIST 10mm 4.2 x 13 Ø5 Ø5 5 x 12 4.2 x 13 4.2 x 13 6203zz 4.2 x 13 4.2 x 22 Ø6 Ø6 4.2 x 19 6 x 16 4.2 x 15 6001zz 608zz 4 x 16 Ø4 4.2 x 13 Ø4 4.2 x 110 4.2 x 22 4.2 x 15 4.2 x 10 Ø6 Ø6 6 x 16 6203zz 4.2 x 13 4.2 x 15 SKU 95088 For technical questions, please call 1-800-444-3353.
PARTS LIST CONTINUED Part 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 Description 1/2” Throat Plate 3/4” Throat Plate 1” Throat Plate 1-1/2” Throat Plate 2” Throat Plate 3” Throat Plate 1/2 “ Sanding Sleeve (80 grit) 3/4 “ Sanding Sleeve (80 grit) 1 “ Sanding Sleeve (80 grit) 1-1/2 “ Sanding Sleeve (80 grit) 2 “ Sanding Sleeve (80 grit) 3 “ Sanding Sleeve (80 grit) 3/4” Rubber Spindle 1” Rubber Spindle 1-1/2” Rubber Spindle 2” Rubber Spindle 3” Rubber Spindle 5/8” OD Spindle
ASSEMBLY DIAGRAM 5 (96, 97, 98, 99, 100, 101) 4 (108, 109, 110, 111,112) 3 (102, 103, 104, 105, 106, 107) 2 (113,114,115) REV 07d, 07i SKU 95088 For technical questions, please call 1-800-444-3353.
ASSEMBLY DIAGRAM CONTINUED 96 99 102 108 SKU 95088 97 100 103 104 109 105 110 98 101 106 111 107 112 For technical questions, please call 1-800-444-3353.
Limited 1 year / 90 day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of one year from date of purchase that the tank is free of defects in materials and workmanship (90 days if used by a professional contractor or if used as rental equipment).
