4.8 VOLT RECHARGEABLE CORDLESS SCREWDRIVER Model 95065 Set up And Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
and sparks. Provide barriers or shields as needed. Specifications Batteries Charging Time Charger Adapter Speed Chuck Features 4.8 V NiCd Battery Pack No more than 10 hours Input: 120 VAC, 60 Hz Output: 6 VDC, 300 mA 200 RPM Hex drive 6 – Driver bits included Electrical Safety 1. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 2. Do not expose power tools to rain or wet conditions.
6. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock. Tool Use and Care 1. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. 2. Do not force the tool. Use the correct tool for your application.
Service 1. 2. Tool service must be performed by qualified repair personnel. Service performed by unqualified personnel could result in a risk of injury. 5. Include vibration-free periods each day of work. 6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work. 7. When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual.
6. Do not force the Cordless Screwdriver. This tool will do the work better and safer at the capacity for which it was designed. 7. Unplug the Charger Adapter from the Cordless Screwdriver and the electrical outlet before use or before performing any inspection, maintenance, or cleaning procedures. 8. Never leave the Cordless Screwdriver unattended while running. Turn power off if you have to leave the Cordless Screwdriver. 9. Grounded Tools: Tools with Three Prong Plugs 1.
1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A.) 3. 4. 0 – 2.0 2.1 – 3.4 3.5 – 5.0 5.1 – 7.0 7.1 – 12.0 12.1 – 16.0 16.1 – 20.0 TABLE A 5.
Unpacking When unpacking, make sure that all the parts are included. See Figure C below. Figure C Charger Adapter Screwdriver Bits Cordless Screwdriver If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Battery Precautions 1. To avoid accidents, never use a different charger adapter with this tool. 2. Do not expose this product to rain or wet conditions. 3.
Charging the Battery 1. Insert the Charger Adapter (24) cord plug into the unit connector as shown below. 2. Plug the Charger Adapter module into an electrical outlet. The red Charging Indicator on the Cordless Screwdriver will light. Charge the new battery for 10 hours. When the battery is fully charged all three LEDs will light up. Remove the Charger Adapter (24) from the electrical outlet. The red Charging indicator will turn off. See Figure D.
Troubleshooting Problem Possible Cause Probable Solution Cordless Screwdriver does not operate when Trigger Switch is pressed. Battery Pack is not charged. Recharge Battery Pack. Battery Pack does not recharge after connecting Charger Adapter for hours. 1. No power to Charger Adapter. 2. Charger Adapter defective. 3. Battery Pack defective. 1. Check electrical outlet for power. 2. Replace Charger Adapter. 3. Replace Battery Pack. Maintenance 1.
Parts List Part 1 2 3 4 5 6 7 8 9 10 11 12 Description Output Axis Gasket Gearbox Ring, Inner, Self-lock Core, Inner, Self-lock Block, Self-lock Gear, Front Star Holder, Star Gear, Middle Gear, Star, Back Gasket, Large Motor Holder Motor Gear Qty 1 1 1 1 1 1 1 1 1 1 1 1 Part 13 14 15 16 17 18 19 20 21 22 23 24 Description Motor Trigger Switch Housing (left / right) LED Indicator Light Cover Light Bulb Switch, Light Connector Pin PDC Battery Pack Charger Socket Charger Adapter Qty 1 1 1 1 1 1 1 1 1 1 1
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
