/ 2” CORDLESS 19.2 VOLT DRILL 94434 OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from that shown in this manual. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND ALL WARNINGS AND INSTRUCTIONS BEFORE USE. Copyright© 2006 by Harbor Freight Tools®. All rights reserved.
Specifications Battery Charger Input 120 VAC / 60 Hz Battery Type NiCd, 19.2 V, 1.7 Ah Battery Charging Time 11/2 Hours Drill Specifications 0-350 RPM / 0-1,300 RPM; Variable Speed; Reversible; 24 Torque Settings; Pistol Grip; Squeeze Trigger Weight 5 lb. with Battery Unpacking When unpacking, check to make sure all the parts shown on the Parts List on page 11 are included.
Electrical Safety 1. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 2. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Personal Safety 1. Stay alert. Watch what you are doing, and use common sense when operating a power tool.
3. Disconnect the power tool from its Battery Pack (22) before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 4. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 5. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control.
This is just an additional precaution; always check for hidden wiring before drilling. 5. Do not use the Cordless Drill or Charger (26) if it has been dropped, damaged, left outdoors, or immersed in liquid. 6. To avoid electrical shock, do not handle the Charger (26), its Power Cord Plug, or the Cordless Drill with wet hands. 7. Keep the Handle of the Cordless Drill dry, clean, and free from oil and grease. 8.
chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code 25249.5, et seq.
(26) is unplugged from its electrical outlet prior to making any adjustments to the tool. (See Figure A.) 2. Chuck (11): Accepts up to 3/8” shank diameter Drill Bits (not included). To install a Drill Bit with the Cordless Drill pointed away from your body, hold the Chuck Sleeve firmly in place and turn the Chuck clockwise. Insert the shank of a Drill Bit all the way into the Chuck. While holding the Chuck Sleeve in place, turn the Chuck counterclockwise to lock the Drill Bit in place. (See Figure A.) 3.
5. NOTE: While charging, the Battery Pack (22) and Charger (26) may become warm to the touch. This is normal, and does not indicate a problem. (See Figure A.) 6. Once the Battery Pack (22) is fully charged, disconnect the Charger (26) from the electrical outlet. Then, disconnect the Charger from the Battery Pack. (See Figure A.) OPERATING INSTRUCTIONS 1. If possible, install the Side Handle (21) to allow better control of the drill.
8. Make sure to hold the Cordless Drill firmly with both hands, as torque from the Motor will cause the tool to twist. FIGURE C TOP VIEW Speed Selector LEVEL RED LIGHT GREEN LIGHT YELLOW LIGHT LIGHT ACTIVATOR 9. O b s e r ve t h e top of the Cordless Drill. (See Figure C.) 10. The Cordless Drill is equipped with a Level that helps the operator drill holes parallel to the floor. (See Figure C.) 11. When depressed, the Light Activator allows the Red, Yellow, and Green Lights to illuminate.
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always turn the Trigger to its “OFF” position, unplug the Charger (26) from its electrical outlet, and disconnect the battery before performing any inspection, maintenance, or cleaning. 2. BEFORE EACH USE, inspect the general condition of the Cordless Drill.
PARTS LIST Part Description Qty. Part Description Qty.
ASSEMBLY DIAGRAM 26 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
