8’ x 10’ GREENHOUSE With Two Vents 93920 Assembly Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com To prevent serious injury, read and understand all warnings and instructions before use. Copyright© 2006 by Harbor Freight Tools®. All rights reserved.
Contents UNPACKING...............................................................................2 SPECIFICATIONS.......................................................................3 Save This Manual................................................................................ 3 GENERAL SAFETY WARNINGS AND PRECAUTIONS...........3 Base Assembly......................................................................5 FRAME ASSEMBLY...................................................................
SPECIFICATIONS Overall Dimensions 120” L x 961/2” W x 865/8” H Window Dimensions 227/8” L x 20” W Door Dimensions 64” H x 24” W x 11/4” Thick Materials Aluminum Frame Transparent Polycarbonate Sheets Aluminum Thickness 0.038” Polycarbonate Sheet Thickness 0.165” Weight 154 lb. Save This Manual You will need this manual for the safety warnings and precautions, assembly, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual.
7. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace or repair damaged or worn parts immediately. 8. REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 9.
Base Assembly Important–Read the following carefully Before Proceeding • The first step in assembly is to assemble a proper base. The greenhouse must be properly supported to help prevent property damage and injury in the event of strong winds or inclement weather. Wind and ground conditions may vary from site to site, and may affect the practicality and effectiveness of anchoring methods substantially.
FRAME ASSEMBLY • Unless noted otherwise, all frame parts will be attached using the Short Bolts (59) and Nuts (61) provided. Bolts should all be assembled with their heads facing the outside of the greenhouse. Tighten Nuts only about 1/4 turn past finger-tight; be careful not to overtighten. • Lay out all parts by number prior to assembly. • An assistant or an appropriate support (not included) will be useful to keep the partially assembled parts upright during assembly.
(44) up under the rail and over the end of the Bolt (59), then 2) secure it using a Nut (61). Use two Hold Down Connectors for each Corner Stud. 3. Remove the Nuts (61) you used in step 1 to assemble the Side Floor Plates (18a, 18b), install a Hold Down Connector (44) over the end of each Bolt (59), and reinstall all Nuts (61). 4. Place three Short Bolts (59) and Nuts (61) into the holes on the Top Doorway Beam (14). Do not tighten them yet.
At this point, the completed section of the frame will likely need support. Attach the second Ceiling Plate the same way. 8. Attach a Corner Bracket (26) at the top of each Corner Stud (1) so that the bracket faces upwards, see diagram to the right. Leave the bottom holes of the two rear Corner Brackets (26) empty to allow the rear brace to be attached to those holes in the next step. 9. Attach the Rear Brace (23) to the inside of the two Corner Brackets (1) that are over the Rear Floor Plate (16).
5. Attach the Front-Center Top Stud (13) to the Front Crown Beams (2,3) using the Top-center Connector (39) as shown below right. 2 3 6. Attach the Rear Crown Beams (4,5) to the Crown (15b) in the same fashion as the Front Crown Beams in step 2. 7. Attach a Corner End Cap (68) onto the outer end of each Crown Beam (2-5). Cover the gaps between 13 39 the Crown Beams (between 2-3 & 4-5) with a Peak Cap (72) in each.
(44) under the base and over the Bolt at each Floor Plate (16) connection. Use Long Bolts (60) for the Rear Brace (23) connections. 2. Attach the tops of the Rear Studs (8, 9, & 10) to the Rear-Right and Rear-Left Crown 5 Beams (4, 5). For the Rear-Center Stud (10), use a 4 Top Center Connector (39) to connect to the Crown Beams, as shown to the right. 3. Refer to the Note in Figure C. Attach the two Side Studs (12) in the center of each side (without asterisks in Figure C) to the outside of the frame.
the Long Bolt at each bottom connection, but do not install a Nut (61) over the Long Bolt yet. 9. Remove the bottom Bolt from the Corner Brackets (26) at the front of the greenhouse. Install the Front Diagonal Braces (24) to the bottom hole of the Brackets on the inside using Long Bolts (60). Attach the bottom of the Front Diagonal Braces (24) to the Long Bolt left exposed on the Floor Plate (17) from the last step. (See Figure C.) 10.
Assembling the Roof Studs and Braces 36 25 11* 11*^ 36 11* Note: 11^ 25 11*^ All Roof Studs (11) marked with an asterisk (*) are 11^ assembled with one Short Bolt (59) in the slot above the Long Bolt(s) (60). All Roof Studs (11) marked with a caret (^) are assembled with two Long Bolts (60) in the slot. All Roof Studs (11) not marked with a caret are assembled with only one Long Bolt (60) in the Slot. 11 25 25 11 Figure D 1.
Assembling the Window 1. Attach the Side Window Frames (34) to the Top Window Frame (33), as shown below to the right. 2. Insert Short Bolts (59) into the holes at the bottom of the Side Window Frames (34), so that the threads stick out the bottom of the window. 33 34 3. Remove the protective film from both sides of the Window Pane (51). Slide the Window Pane (51) into the three-sided frame. 4. Slide the Bottom Window Frame (35) onto the two Short Bolts (59) and the Window Pane (51).
3. Orient the assembled door frames for so that the Outer Door Frame (27a) is on the left, and the Inner Door Frame (27b) is on the right. This is the assembly used for the left door, the right door will be assembled later with the Outer and Inner Door Frames on the opposite sides (outer on right, inner on left). All illustrations show the left door assembly. 4. Attach the Top Door Frame (30) to the top of the Outer/Inner Door Frames (27a, 27b).
Installing the Transparent Panels 1. Panel Clips (67) are used to secure the Transparent Panels in place on the Greenhouse. 2. Remove the protective film from both sides of all panels. 48/50 15a/15b 35 48 48 50 36 20a/20b 3. The Roof Panels (48) and the Roof Window Panel (50) will need to be placed as shown in the illustrations above. The top edges of these panels need to be placed up under the edge of the Crown (15a, 15b) or the Window Support Beam (36). 4.
Panel Installation Diagram # # # ## # ## # = Panel Clip (67) Location ## # ## ## ## # 52 49 52 # # # ## # 51 # 48 # # # ## # # ## 48 51 # 50 ## ## ## # # 48 48 ## 48 48 # # ## 47 # ## # ## 47 ## # # ## # 47 47 ## 49 # # 53 55 55 ## ## # ## ## 55 # ## ## # 54 # # # # # # # ## ## # 48 # 54 # ## ## # # # # # # ## ## ## ## ## # # 48 # ## ## ## ## 47 # ## # # # # # ## ## # # ## ## ## ## # 50 ## # ## 49 # ## # ##
INSPECTION, MAINTENANCE, AND CLEANING 1. BEFORE EACH USE, inspect the general condition of the Greenhouse. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, and any other condition that may affect the safe operation of the Greenhouse. If a problem occurs with the Greenhouse, have it corrected before further use. Do not use damaged equipment. 2. TO CLEAN: Wipe with a damp cloth, using a mild detergent.
PARTS LIST Lengths given are approximate and rounded to the nearest inch.
PARTS LIST (continued) Part lengths are approximate and rounded to the nearest inch. Part Description Q’ty Part Description Q’ty 2 55 Door Top/Bottom Panel 2’ x 1’ 11” 4 39 Top Center Connector 40 Front/Rear Base Plate 8’ 2 56 Long Door Support Bolt M6 x 33 mm 2 41a Side Base Plate A 8’ 2 57 Door Screw ST4.3 x 19 mm 32 41b Side Base Plate B 2’ 2 58 Window Screw ST4 x 7.
