® FLOOR STAPLER WITH HAMMER Model 93197 ASSEMBLY and OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Specifications Air Inlet Recommended Air Pressure Maximum Air Pressure Dimensions Weight Magazine Capacity Air Consumption Fastener Size Range 1/4” - 18 NPT 70-90 PSI 100 PSI 22-1/2” x 17-1/2” x 3-1/8” 21.85 Lbs. 80 Pcs. / Top Loaded 5.0 CFM @ 80 PSI 3/4” to 2” Long x 15 Gauge Note: SKU 90429 - 2”, 15 Gauge Staples are available from Harbor Freight Tools. Note: This Floor Stapler is designed for use on wood floors.
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 8. Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working around metal, wood, and chemical dusts and mists.
Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Operation (continued) Assembly - Attaching the Arm (48) is the only assembly required. See FIGURE 1 and the Assembly Drawing on page 8. The two Clamp Screws (44) fit in the recessed gaps on the lower part of the Arm (48). As shown below, hold the Clamp Screws (44) in place around the Body (18) and add a Washer (45) and a Nut (46) to the threaded ends of the Clamp Screws (44). Tighten them securely. FIGURE 1 Clamp Screws (44) Staples exit the Stapler from the bottom of the Shoe (28).
Operation (continued) Using the Floor Stapler THIS TOOL DOES NOT USE A SAFETY MECHANISM; extreme caution must be used whenever this tool is connected to an air supply. If the tool is dropped or if the Hammer Face (10) is accidentally struck, then the tool will fire a staple, potentially causing SEVERE PERSONAL INJURY. 1. Connect the Floor Stapler to the air hose and turn on the FIGURE 3 air compressor. Note: Before using on a floor, test the unit on a scrap piece of wood.
Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. 2. 3. 4. Disconnect the Stapler from the air hose. Empty Magazine (30a) completely. Attempt to fire the Stapler into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any staples. Always leave Magazine Cover (33a) open during maintenance. The Magazine is spring-loaded and may cause parts or a staple to fly out of the Stapler. Clearing Jams 1. 2. 3. 5. 6. 7. 8. 9. 10. 11.
Parts List Part Description Part Description 1 Cylinder Bushing 26 Screw 2 Plunger 27 Spacer for 25/32" Flooring 3 0-ring 27a Spacer for 1/2" Flooring 4 0-ring 28 Shoe 5 Poppet 29a Pin 6 0-ring 30a Magazine 7 0-ring 31a Magazine Cap 8 0-ring 32a Screw 9 Piston Assy.
Assembly Diagram #27 - Installed: (Spacer for 25/32” Flooring) #27a - Spacer is included with tool, not installed (Spacer for 1/2” Flooring) SKU 93197 For technical questions, please call 1-800-444-3353.
