Table of Contents Safety Safety.......................................................... 2 Specifications.............................................. 5 Setup........................................................... 6 Operation..................................................... 7 Maintenance............................................... 10 Parts List and Diagram................................ 2 Warranty.....................................................
1. Do not install this inverter into a building’s electrical system. This inverter is a vehicular accessory. It is not designed to be safely used in a building’s electrical system and has not been evaluated to meet building wiring codes. Improper application may create a fire or electric shock hazard. 7. Keep inverter dry and clean. Do not expose to rain, snow, spray, bilge water or dust. 2.
Operation Precautions (cont.) Safety 5. Check for breakage of parts and any other condition that may affect the Inverter’s operation. If damaged, have it repaired before use. 8. Do not attach a battery charger if the charger carries a warning that dangerous voltages are present at the battery terminals. 6. Do not attempt to power a device, or combination of devices, that will require more than the rated output of this inverter. This may damage the inverter or the attached devices. 9.
Input Voltage 12 VDC (nominal) Output Voltage 115 V~ / 60 Hz Continuous Power 750 W Surge Power 1500 W Operating Conditions 32° - 104° F Safety Specifications Two 3-prong grounded polarized AC outlets One 5 VDC 500mA USB outlet One 35 Amp Internal Blade-type Fuse (professional replacement only) Receptacles Fuse Type Overall Dimensions 9-1/4" L x 5-1/4" W x 2-1/2" H 12 10 10 10 8 8 8 6 6 16 14 12 10 10 8 8 8 6 6 6 16 14 10 10 8 8 6 6 6 6 4 16 14 10 10 8 8 6
Installation Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Power Switch is in the off‑position and unplug the tool from its electrical outlet before performing any procedure in this section. CAUTION! This Inverter must only be connected to batteries with a output voltage of 12 volts DC.
Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Tool Set Up TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that all Power Switches/Triggers are in the off‑position and unplug the tool from its electrical outlet before performing any procedure in this section. 2.
Operating Tips The total wattage of all items plugged into the Power Inverter must not use more than 750 watts during continuous operation, otherwise the Inverter may overload. Safety If an alarm sound is heard, turn off the appliances and check the Troubleshooting Tips section to correct the issue before continuing. Caution: Some rechargeable appliances may damage the Power Inverter or the appliance. When first using a rechargeable device, check the inverter’s temperature for the first 10 minutes.
Troubleshooting Tips If the alarm sounds, this means that the input voltage is at or below 10.9 V. The battery needs recharging. You should stop using the Power Inverter and recharge the battery. If this is not done, the Inverter will shut off automatically at 10.5 V. • If you are unsure if the inverter will have the proper amount of current to run your devices, add up the total of the continuous wattage for the items.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that all loads are disconnected from the Inverter, the Power Switch is in the off‑position and the cables are disconnected from power source before performing any procedure in this section. To prevent serious injury from tool failure: Do not use damaged equipment.
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
3491 Mission Oaks Blvd.
