0” Heavy-Duty 15 AMP Table Saw 66630 Set up and Operating Instructions Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
NOTICE is used to address practices not related to personal injury. Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
7. 8. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 100’ 150’ 0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. TABLE A 9. USE PROPER EXTENSION CORD.
or other part that is damaged should be properly repaired or replaced. 20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only. 21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. Table Saw Safety Warnings For Your Own Safety Read Instruction Manual Before Operating Saw 1. Wear eye protection. 2.
controlled workpiece to lift up and out of the saw toward the operator. Kickback is usually a result of tool misuse and can be limited or avoided by following the precautions below: • Fence must be completely parallel to the saw blade. • Workpiece must be free from flaws (such as loose knots) and from foreign objects (such as nails and screws). movable guard does not move freely and close instantly. Make sure any movable guard does not touch the blade in all angles, depths of cut, and positions. 12.
Essential Straight Push-stick Features and Functions Note: Straight style (traditional) stick shown. A different stick design may be used if it properly protects against all hazards. Diagram not to scale. Handle Notch • Must be far enough down the stick to allow a comfortable and firm grip. • Push sticks must be made from sturdy, defect-free, plywood or normal wood to prevent unexpected breakage. Material must be at least 1/4” thick ,but no thicker than the finished wood.
14. When servicing use only identical replacement parts. 15. Only use safety equipment that has been approved by an appropriate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area. 16. Industrial applications must follow OSHA guidelines. 17. Maintain labels and nameplates on the tool. These carry important safety information.
reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool.
stood, or if in doubt as to whether the tool is properly grounded. 5. Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. 6. Repair or replace damaged or worn cord immediately. 7. This tool is intended for use on a circuit that has an outlet that looks like the one illustrated above in 125 V~ 3-Prong Plug and Outlet. The tool has a grounding plug that looks like the plug illustrated above in 125 V~ 3-Prong Plug and Outlet. 8.
Specifications Electrical Requirements 120 V~ / 60 Hz / 15 A Motor No Load Speed 4800 RPM Blade Diameter 10” Arbor Diameter 5/8” Table Surface 16”x 26” Cutting Depth at 0° 3” Cutting Depth at 45° 2-3/8” Overload Protection Breaker Switch Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Assembly To Install Handwheel (29) 1. Remove the Bolt (27) from the Screw Rod (54). 2.
(109) and that the tabs are on the INSIDE slot of the Splitter. 8. Use a framing square (not included) to make sure the Saw Blade and Splitter assembly are square. If not square, loosen the Splitter Bracket and adjust until the Splitter is properly aligned with the Saw Blade. Then tighten all screws and bolts. Mounting 1. The Saw MUST be properly secured to the supporting surface using the four mounting holes at each corner of the Base (5). 2.
7. The Blade (96) depth should be set so that outer points of the Blade are 1/8” to 1/4” higher than the workpiece while the lowest points are below the workpiece. Please note: When the Blade is at 90° to the Table Saw, the Blade should be square with the Saw Table. 8. WARNING! The Bevel Lock Knob must be tightened during all cutting operations. 2. To raise the Blade, turn the Handwheel (29) counterclockwise. 45° and 90° Positive Stop Adjustment 3. To lower the Blade, turn the Handwheel clockwise.
with or slightly below the Table surface. Aligning and Adjusting the Rip Fence (146) 1. 2. WARNING! A misaligned Fence can cause kickbacks and jams. To reduce risk of injury, always maintain proper Fence alignment. The Rip Fence must be parallel with the Blade and Table grooves. Lift up the Fence Handle (26) and move the Fence along the gauge slot until sliding it to the desired location. 3. Verify that Fence is parallel, then push down on the Handle to lock the Fence in place. 4.
edge of the square until it touches the marked tooth. 7. 8. FENCE (146) Rotate the Blade and check the same marked tooth at the rear of the Table Saw. FRONT OF TABLE SAW If the front and rear measurements are not identical, have a qualified service technician repair the Table Saw. Wood Block FIGURE B Installing/Replacing Saw Blade 1. WARNING! Make sure to unplug Table Saw before making any installing or replacing Blade. 2.
because of overloading (such as cutting stock too fast or when using a dull blade), first turn the Switch to the “OFF” position. Work Piece and Work Area Set Up 1. 2. 3. 4. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage.
7. When making a cut, use steady and even pressure. Do not force cuts. 8. Do not cut wet or warped lumber. 9. Hold the workpiece firmly with both hands or use the included Push Stick. (53). Make sure the Push Stick is narrower than the workpiece and has 90° notch on one end and shaping for a grip on the other end. Hand furthest from Blade on the workpiece. 9. Once cut is made, turn off Table Saw. Wait for Blade to come to complete stop before removing any part of workpiece. Making a Rip-cut 1. 10.
To reduce possible injury should kickback occur, stand to side of the workpiece as it contacts the Blade. WARNING! Do not stand in the line of cut. 6. Once cut is made, turn off Table Saw. Wait for Blade to come to complete stop before removing any part of workpiece. Making a Bevel Rip-cut 1. WARNING! The Fence must be on the right side of the Blade to avoid trapping the wood and causing kickback.
Maintenance And Servicing 4. To maintain the surface of the Table, periodically apply paste wax and buff to keep Table surface smooth. WARNING! Do not wax the working face of Miter Gauge. Doing so may cause a workpiece to slip during cutting, leading to possible injury. 5. After Use, clean out sawdust from underneath Table Saw and in Blade teeth. Use a resin solvent on the blade teeth. Dry with soft cloth. 6. Use soft, damp cloth to clean plastic parts.
Parts List Part 1 2 3 4 5 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Description Rubber feet Bolt M6×25 Spring washer Mat washer Base Bolt ST4.2×14 Sheathing Cable press plate Bolt M4×16 Strengthen plank Bolt M4×8 Ruler Nut M4 Washer Switch Key Switch Bolt ST4.
Parts List Part 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 Description Table Bolt M6×25 Bolt M6×35 Table insert Blade Guard Bolt M6×12 Nut M6 Pivot Bolt M6×50 Pivot Plate Bolt M6X16 Splitter Bracket Bolt M6×12 Wing Nut M6 Twist spring Axis cover2 Block plate Quakeproof mat Bolt M6×40 Armature Axis cover3 Column pin Spring column pin Parts List Qty.
ASSEMBLY DIAGRAM SKU 66630 For technical questions, please call 1-800-444-3353.
Limited 1 year / 90 Day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship.
