texture paint spray gun 66103 Set up and Operating Instructions Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
Save This Manual NOTICE is used to address practices not related to personal injury. Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
sure to high intensity noise is able to cause hearing loss. Personal safety a. Stay alert. Watch what you are doing and use common sense when operating. Do not use while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating increases the risk of injury. b. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts.
e. Maintain the tool with care. Keep this tool clean. A properly maintained tool is easier to control. f. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged. g. Use only accessories that are identified by the manufacturer for the specific tool model.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm).
ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use.
Functional Description Air Supply To prevent explosion: Use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. Specifications Operating Air Pressure Range 25 - 90 PSI Maximum Air Pressure 90 PSI Air Inlet 1/4” -18 NPS Air Consumption 7 CFM @ 25 PSI Nozzle Size 4 mm (5/32”) 6 mm (15/64”) 8 mm (5/16”) Hopper Capacity 1.
operate accidentally after the air supply is disconnected. Note: Air flow, and therefore tool performance, can be hindered by undersized air supply components. 2. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 3. Make sure the tool’s throttle or switch is in the off position; refer to Operation section for description of controls. 4. Close the in-line safety valve between the compressor and the tool. 5.
Work Piece and Work Area Set Up 4. 1. 2. This Texture Paint Spray Gun is meant for spraying heavy viscosity products like rubberized decking materials, texture coatings for interior and exterior walls, heavy water proofing materials, and the like. It is not recommended for regular wall paint or thin coatings of any type. While these products can be used with this Spray Gun, the results would not be satisfactory, or even in coverage. Designate a work area that is clean and well-lit.
8. When you are completely finished or are stopping for the day, disconnect and empty the Plastic Hopper. Flush the system with fresh cold water. Rinse and clean the Plastic Hopper and the Gun Body and let both dry completely before storing inside, away from children. 9. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool.
Troubleshooting Problem Possible Causes Decreased output. 1. Not enough air pressure and/ or air flow. 2. Obstructed trigger. 3. Blocked air inlet screen (if equipped). 4. Air leaking from loose attachment. 5. Mechanism contaminated. Severe air 1. Cross-threaded housing leakage. components. (Slight air leakage is normal, 2. Loose housing. especially on older tools.) Product not spraying correctly. 3. Damaged valve or housing. 4. Dirty, worn or damaged valve. 1. Material too thick/thin. 2.
PARTS LIST Part 1 2A 2B 2C 03 04 06 07 08 8A 8B 8C 8D 8E Description Retaining Ring 4.0 mm (3/16”) Nozzle 6.0 mm (1/4”) Nozzle 8.
Limited 1 Year warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment).
