0” DISC SANDER – BENCH TYPE Model 47404 Set up And Operating Instructions Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed Exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual.
SPECIFICATIONS TABLE Electrical Requirements Sanding Disc Diameter Sanding Disc Type Dust Collection Port Table Dimensions Table Tilt Angle Table Tilt Scale Increments Miter Gauge Scale Base Mounting Holes Base Dimensions 120 V / 60 Hz / 3/4 HP / 13.4 Amps Single Phase / 1,750 RPM 10” Pressure Sensitive Adhesive (PSA) 1-3/8” O.D.
caught in moving parts. Wear a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a long-sleeve shirt, roll sleeves up above elbows. 7. DO NOT OVERREACH. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etcetera. 8. INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENT. 9. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not use this product when you are tired or distracted from the job at hand.
2. GROUND THIS PRODUCT. The electrical Power Cord/Plug (part #34) for this product is equipped with a grounded, 3-prong Plug. Never remove the grounding prong or modify the Plug in any way. Do not use adapter plugs with this product. To comply with the National Electric Code, and to provide additional protection from the risk of electrical shock, this product should only be connected to a 120 Volt, 3-hole electrical outlet that is protected by a Ground Fault Circuit Interrupter (GFCI). (See Assy. Diagram.
material faster than it was designed to sand. 12. DO NOT ATTEMPT TO SAND WORKPIECES TOO SMALL TO SAFELY HOLD BY HAND. Attempting to hold onto a very small workpiece will bring fingers and hands in dangerous proximity to the spinning sanding disc. 13. WHEN SANDING A LARGE WORKPIECE, MAKE SURE IT IS PROPERLY SUPPORTED AT THE WORK TABLE (part #7) HEIGHT. 14. NEVER LEAVE THE DISC SANDER UNATTENDED WHEN IT IS RUNNING. Turn off the machine, and wait until it has completely stopped before leaving. 15.
ASSEMBLY INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12. To Assemble The Disc Sander: 1. CAUTION: Prior to performing this procedure, make sure the Safety Switch (part #32) of the Disc Sander is in its “OFF” position and the Power Cord/Plug (part #34) is unplugged from its electrical outlet. (See Figures C, D, and Assy. Diagram.) 2.
MACHINE ADJUSTMENT INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12. To Adjust The Table Angle: 1. CAUTION: Prior to performing this procedure, make sure the Safety Switch (part #32) of the Disc Sander is in its “OFF” position and the Power Cord/Plug (part #34) is unplugged from its electrical outlet. (See Figures C, D, and Assy. Diagram.) 2. The Work Table (part #7) may be angled downward from 0 to 45 degrees.
2. The Miter Gauge (part #3) may be angled from 0 to 60 degrees, right or left. To do so, slightly loosen the Knob (part #1). Move the Miter Gauge horizontally to the right or left until the Pointer (part #5) indicates the desired angle. Then, firmly retighten the Knob Bolt. (See Figures B, D, and Assy. Diagram.) FRONT VIEW MITER GAUGE (#3) MITER GAUGE (#3) KNOB (#1) KNOB (#1) SAFETY SWITCH (#32) POINTER (#5) SAFETY SWITCH (#32) POINTER (#5) FIGURE D To Attach A Sanding Disc To The Disc Sander: 1.
OPERATING INSTRUCTIONS NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12. 1. CAUTION: Prior to beginning to use, make sure the Safety Switch (part #32) is in its “OFF” position and the Power Cord/Plug (part #34) is unplugged from its electrical outlet. (See Figures C, D, and Assy. Diagram.) 2. Make all necessary adjustments to the Disc Sander as previously discussed.
INSPECTION, MAINTENANCE, AND CLEANING NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 12. 1. CAUTION: Always turn the Safety Switch (part #32) to its “OFF” position, unplug the Power Cord/Plug (part #34) from its electrical outlet, and wait until the Sanding Disc (part #14) has completely stopped spinning before performing any inspection, maintenance, or cleaning. 2. BEFORE EACH USE, inspect the general condition of the Disc Sander.
PARTS LIST Part 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Description Knob Screw (M5 x 6) Miter Gauge Washer Pointer Gauge Sliding Bar Work Table Round Body Threaded Rod Washer Table Lock Assembly Knob Bolt Spring Spring Adjusting Screw Sanding Disc Disc Washer Screw (M6 x 12) Dust Cover Screw (M5 x 8) Spring Washer Big Pointer Screw (M5 x 16) Base Screw (M5 x 12) Rubber Pad Screw (M5 x 20) Motor Housing Qty.
NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 47404 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
