AIR FILTER SYSTEM - REMOTE CONTROL Model 46361 OPERATING INFORMATION ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2001 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
SPECIFICATIONS TABLE % ! ** + 6 7 + & % % <+ ; & % ? @ & 6 ? @ & ; %E ! " # #$ & ' & ( ) /5 ' & 8: ; ' ) = > /= > = D= > = > = 8 = > 8 D= = 7' SAVE THIS MANUAL You will need this manual for the safety warnings and precautions,
6. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that the Air Filter System will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this machine. Replace or repair damaged or worn parts immediately. 7. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product.
5. MAKE SURE THE POWER SWITCH (part #19) IS IN THE “OFF” POSITION BEFORE PLUGGING IN THE POWER CORD. 6. DO NOT ABUSE THE POWER CORD. Do not yank the Power Cord (part #8) to disconnect it from the electrical receptacle. Do not move this machine with the power cord in the outlet. Keep the cord away from heat, oil, and sharp edges. 7. IF YOU USE AN EXTENSION CORD, MAKE SURE TO USE ONLY UL APPROVED CORDS HAVING THE CORRECT GAUGE AND LENGTH. (SEE FIGURE A.
UNPACKING When unpacking, check to make sure all parts shown on the Parts List (page 11) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: All parts listed below refer to the parts listed and shown on pages 10 and 11 of this manual. Placement Of The Air Filter System: 1.
5. Locate the desired ceiling location, and ceiling joists, upon which to attach the Air Filter System. 6. With assistance and proper lifting equipment (not provided), raise the Air Filter System to the desired ceiling location. Caution: Make sure all other people are kept well clear of the surrounding area during this procedure. 7. Align the four Hangers (part #31) with the ceiling joists and measure for eyelet bolt location.
2. When the manual Power Switch (part #19) is turned to its “NON-REMOTE CONTROL” position, the Air Filter System will run continuously until the manual Power Switch is turned to its “REMOTE CONTROL” position. The Air Filter System will then automatically shut off. (See Figures D, G, and Assy. Diagram.) 3. The Air Filter System may also be operated by a hand held Remote Control (part #34). The Remote Control has an operating range of up to 25 feet. (See Figure E, and Assy. Diagram.
4. NOTE: The Remote Control requires a 9 Volt battery. To install a 9 Volt battery in the Remote Control, remove the Battery Cover located on the back of the Remote Control and connect the battery poles to the Battery Lead on the Remote Control. Then, replace the Battery Cover. (See Figure E, and Assy. Diagram.) 5. To begin using the Remote Control (part #34) feature, turn the Power Switch (part #19) to its “REMOTE CONTROL” position and leave it in that position.
CLEANING AND MAINTENANCE 1. Caution: Always disconnect the Air Filter System from its electrical supply source before performing any cleaning, servicing, or maintenance. 2. Before each use, inspect the general condition of the Air Filter System. Check for loose screws, misalignment, binding of moving parts, broken parts, loose or damaged electrical power cord, and any other condition that may affect its safe operation.
FILTER BAG (#2) FIGURE I 5. If necessary, wipe the outside of the Air Filter System with a damp cloth. You may use a mild detergent. PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
PARTS LIST Power Cord 34 REMOTE CONTROL 1 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
