8” Drill Press Model 44506 Set up and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2010 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
Contents Important SAFETY Information ���������������������������������3 Maintenance And Servicing ���12 Cleaning, Maintenance, and Lubrication ������������������������������������ 12 Troubleshooting ��������������������������� 14 General Tool Safety Warnings � 3 Parts Lists and Diagrams ������15 Grounding Instructions ����������5 110-120 V~ Grounded Tools: Tools with Three Prong Plugs 5 Drill Press Safety Warnings ����� 5 Specifications �������������������������������8 Unpacking �����������������������
NOTICE is used to address practices not related to personal injury. Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 100’ 150’ 0–6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. TABLE A 9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition.
3-pole receptacles that accept the tool’s plug. Grounding Instructions To prevent electric shock and death from incorrect grounding wire connection Read and follow these instructions: 6. Grounding Pin 110-120 V~ Grounded Tools: Tools with Three Prong Plugs 1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
5. The included chuck key is specially designed to be self-ejecting, reducing the risk of ejecting at high speed. Only use the included chuck key or an identical replacement key. 6. Do not operate with ANY guard disabled, damaged, or removed. 7. The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury to persons. 8. When servicing use only identical replacement parts. 9.
medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use.
Specifications Electrical Input Motor Speed Spindle Speeds Spindle Stroke Base Throat Depth Chuck Table Rotation Table Size Table Slot 120 V~, 60 Hz, 1/3 HP (3.6 A) 1750 RPM (No Load) 620, 1100, 1720, 2340, and 3100 RPM 2” 11-1/8” x 7”; Slot: 9/16” 4” (of 8” swing) 1/2” 360°; Tilt: 45° (left and right) 6-5/8” x 6-3/8” 5/8” Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.
(C3). Slide it down on the Column Tube as far as it will go. Align it so that it faces straight forward, inline with the Base. 6. Thread in two Set Screws (11), into the side of the Head (1) and tighten. 7. Attach Knob (A2) to the (top) pulley Guard (A5) using Pan Head Screw (A3). 8. Adjust Belt (A4) tension: dirt, grease, oil, and protective coatings (paint thinner may be necessary). b. Slide the Chuck onto the Spindle Shaft. c. Turn the Chuck sleeve clockwise and open the jaws completely. d.
Operating Instructions Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Spring Cap (29) Hex Nuts (30) Tool Set Up To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
with enough extra length to allow free movement while working. 3. 4. Clamp workpiece or brace against column to prevent rotation. There must not be objects, such as utility lines, nearby that will present a hazard while working. General Operating Instructions 1. Secure the tool to a supporting structure before use. 2. Make sure the Drill Press is OFF and the Power Cord (33) is unplugged. Loosen the Lock Handle Support (C2) and adjust the Table height to accommodate the workpiece being drilled.
Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment.
Adjusting the Feed Wheel Return Tension Spring 8. Pull the Feed Knob and check the spring tension, making sure the up movement is smooth and complete. From one inch down, the Chuck should return to its uppermost position. If more tension is required, repeat steps. 9. Replace the (outer) Hex Nut and tighten on top of the (inner) Hex Nut. Do not overtighten. CAUTION! Wear an ANSI-approved full face shield during this procedure. 1. 2. Move the Chuck to its uppermost position.
Troubleshooting Problem Tool will not start. Possible Causes Likely Solutions 1. Cord not connected. 2. No power at outlet. 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Internal damage or wear. 3. Have technician service tool. Tool operates slowly. Extension cord too long or wire size Eliminate use of extension cord.
PLEASE READ THE FOLLOWING CAREFULLY The manufacturer and/or distributor has provided the parts list and assembly diagram in this manual as a reference tool only. Neither the manufacturer or distributor makes any representation or warranty of any kind to the buyer that he or she is qualified to make any repairs to the product, or that he or she is qualified to replace any parts of the product.
Head Assembly Diagram Page 16 For technical questions, please call 1-800-444-3353.
Parts List and Diagram A - Pulley and Spindle Part Description A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 Bushing, Rubber Knob Screw, Pan Hd., M5x0.8-12 Belt, V5, 5/16x26 Guard with Labels Screw-washer Hd., M6x10-16 Ring, Retaining Bearing, Ball, 17 mm Spacer Insert, Pulley Pulley, Spindle Nut, Pulley Clamp, Cord Screw, Pan Hd., M5x0.8-16 Washer, Foam When ordering a part from this drawing, add an “A” prefix to the part number. SKU 44506 For technical questions, please call 1-800-444-3353.
Parts List and Diagram B - Chuck and Spindle Shaft Part B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 Description Gasket, Quill Bearing, Ball, 12 mm Tube, Quill Screw, Pan, M5x0.8-20 Collar, Stop Ring, Retaining Shaft, Spindle Chuck Chuck Key Nut, Hex, M6x1.0 Nut, Hex, M5x0.8 Stop, Rod When ordering a part from this drawing, add a “B” prefix to the part number. Page 18 For technical questions, please call 1-800-444-3353.
Parts List and Diagram C - Base and Table Part Description C1 C2 C3 C4 C5 C6 C7 Support, Table with Scale Support, Lock Handle Tube, Support Base Screw, Hex Hd., M8x1.25-20 Screw, Hex Hd., 1/2-12x7/8 Table When ordering a part from this drawing, add a “C” prefix to the part number. SKU 44506 For technical questions, please call 1-800-444-3353.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
