Table of Contents Safety Safetye�������������������������������������������������2 Specifications......................................6 Setup...................................................7 Operationa��������������������������������������������7 Maintenancei���������������������������������������9 Parts List and Diagram.......................10 Warranty.............................................12 WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol.
2. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 3. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 4. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
Safety 5. Maintain power tools. Check for 6. Use the power tool, accessories and misalignment or binding of moving tool bits etc. in accordance with these parts, breakage of parts and any other instructions, taking into account the condition that may affect the power tool’s working conditions and the work to operation. If damaged, have the power be performed. Use of the power tool for tool repaired before use.
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. Table A: Recommended Minimum Wire Gauge for Extension Cords* (120/240 Volt) 150´ 100´ 75´ (at full load) 50´ 8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas. EXTENSION CORD LENGTH 25´ Safety NAMEPLATE AMPERES Setup 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.
Setup - Before Use: Safety Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Workpiece and Work Area Set Up Safety 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Vehicle exhaust fumes and accumulated refrigerant gas can kill you. Do not operate vehicle’s engine or service air conditioner in enclosed or poorly ventilated area. 3. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage.
Maintenance and Servicing Safety Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Parts List and Diagram Safety PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Safety 37- 9 378 377 6 37- 3 37- 2 8 9 10 11 12 13 37- 4 37- 1 14 15 16 17 18 19 Setup 10 37- 20 21 22 23 24 25 26 Operation 375 46 27 43 28 29 30 31 32 33 44 42 41 34 35 36 Maintenance Assembly Diagram 12 11 1 2 3 4 5 6 7 373737- 49 48 47 45 37 38 39 40 Page 11 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
