Table of contents SAFETy Safety ......................................................... 2 Specifications ............................................. 8 Setup .......................................................... 9 Operation ................................................... 10 Maintenance .............................................. 11 Parts List and Diagram .............................. 14 Warranty ....................................................
1. power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 2.
7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. SAFETy Service Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Drill Safety Warnings 1.
Vibration Safety 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool.
Grounding SAFETy TO pREVENT ELEcTRIc SHOcK AND DEATH FROM INcORREcT GROUNDING WIRE cONNEcTION: check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use.
6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure the extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect the extension cords from sharp objects, excessive heat, and damp or wet areas.
Specifications SAFETy Electrical Rating 120V~ / 60Hz / 3.5 A No Load Speed 0 –1450 RPM Chuck Capacity 1/16" – 3/8" 4005982 SETUp OpERATION MAINTENANcE Page 8 For technical questions, please call 1-800-444-3353.
Setup - Before Use: Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETy Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 14.
Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETy Tool Set Up TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Make sure that the Trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section.
Maintenance and Servicing SAFETy procedures not specifically explained in this manual must be performed only by a qualified technician. TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Make sure that the Trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section. TO pREVENT SERIOUS INJURy FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Troubleshooting problem Tool will not start. possible causes 1. Cord not connected. 2. No power at outlet. SAFETy 3. Tool’s thermal reset breaker tripped (if equipped). 4. Internal damage or wear. (Carbon brushes or Trigger, for example.) Tool operates slowly. 1. Forcing tool to work too fast. 2. Extension cord too long or cord diameter too small. SETUp Performance 1. Carbon brushes worn decreases over time. or damaged. 2. Bit dull or damaged. Excessive noise Internal damage or wear.
MAINTENANcE OpERATION SETUp THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
parts List and Diagram parts List SAFETy part SETUp 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Description Screw M5 x 20 Spring Washer 5 Drill Chuck Screw M4 x 14 Spring Washer 4 Gearbox Cover Retaining Ring 15 Bearing 6002 Output Spindle Pin 4 x 12 Gear Z4 Gear Z5 Bearing 607 Gear Z3 Gear Z2 Bearing 625 Gear Box Spindle Gear Protective Plate Link Bushing Bearing 608 Qty 1 1 1 3 3 1 1 1 1 3 3 1 3 1 1 1 1 1 1 1 1 part 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Descript
MAINTENANcE OpERATION SETUp SAFETy Assembly Diagram Item 60610 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
