NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Table of Contents Safety Safetye��������������������������������������������������������� 3 Specifications.............................................. 6 Setup........................................................... 7 Operationa��������������������������������������������������� 10 Maintenancei���������������������������������������������� 12 Parts List and Diagram............................... 14 Warranty...................
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. Assembly Precautions 1. Assemble only according to these instructions. Improper assembly can create hazards. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. 3.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Grounding Safety TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE CONNECTION: Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 - - 16.1 – 20.0 12 10 - - - * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. Extension Cord Safety 0 – 2.0 a. Make a knot as shown below then connect the cords: Appliance Cord 2 1 b.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Vibration Safety Safety This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: Setup 1.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool off before performing any procedure in this section.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. 8. With assistance, set the Lower Drum (48) with attached Arm (77) and Support Bracket Seats (35) into Stand assembly and align the bolt holes. See Figure D. Safety Support Bracket Seat (35) 14. Use gasket sealer (not included) to stick the Rubber Gasket (60) to the Upper Drum (59), making sure the holes in both align. The Gasket must be flat on the Upper Drum to ensure a proper seal. 15.
NOTICE 22. Spread a few drops of lubricating oil on the Pinion Shaft and squarely push the Drum Pulley (26) onto the Shaft so that the groove in the Pulley engages the Flat Key (25). The Pulley should be flush with the step on the Pinion Shaft. Note: Do not hammer the Drum Pulley onto the Pinion Shaft. Doing so can damage the unit and possibly lead to a loose fitting V-Belt (68). 23. Place the Motor (65) onto the Motor Bracket. 24.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Operating Instructions Safety Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Functions Motor Assembly Upper Drum Control Handle Mixer Blade Setup Handle Control Plate Stand Wheel Bracket Lower Drum Operation Wheel Arm Leg Maintenance Page 10 For technical questions, please call 1-888-866-5797.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. 1. Place the Cement Mixer on a solid, even surface. 5. Flip the switch to “ON” (I) position. WARNING! Do not attempt to move the Cement Mixer when it is full and/or in operation. Block the wheels with wheel chocks (not included). 6. Once materials are mixed, tilt Drum and dump materials where needed. The materials are dumped while the Drum is rotating. 2.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Maintenance and Servicing Safety Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch of the tool to its “OFF” position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Troubleshooting 3. Internal damage or wear. Tool operates slowly. Extension cord too long or wire size too small. Excessive noise or rattling. Overheating/ Overloading. 1. Belt too loose (slipping) or too tight (bearing damage). 2. Internal damage or wear. 1. Running at 100% load for extended time. 2. Blocked motor housing vents. 3. Motor being strained by long or small diameter extension cord. Likely Solutions 1.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix. Parts List and Diagram Safety Parts List Part Setup Operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Description Cotter Pin 5×40 Flat Washer 27 Wheel Wheel Bracket Hex Flange Nut M8 Motor Bracket Power Cord Bushing M12 Motor Cover Flat Washer 4 Cross-Head Screw M4×12 Screw ST3.5×9.
NOTICE FOR CEMENT AND MORTAR ONLY. Do not use with Epoxy 2-part resin mix.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
