Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference. 20 gauge wide crown stapler Visit our website at: http://www.harborfreight.
Table of Contents Safety Safety.......................................................... 2 Maintenance............................................... 14 Specifications.............................................. 7 Setup........................................................... 9 Operation.................................................... 12 Parts List and Diagram............................... 17 Warranty.....................................................
IMPORTANT SAFETY INSTRUCTIONS Safety INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING – When using tools, basic precautions should always be followed, including the following: General To reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. Work area a. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric shock, fire, and injury to persons. c.
Tool use and care Safety a. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and can lead to loss of control. b. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed. c. Do not use the tool if the trigger does not turn the tool on or off.
Specific Safety Instructions 3. Choice of triggering method is important. Check manual for triggering options. Safety 20. Do not fire fasteners into a workpiece that has people, utility lines, or other objects behind or inside it. 5. Do not point the tool toward yourself or anyone whether it contains fasteners or not. 21. Keep balance while using this tool. Keep area below clear if working in an elevated location, and secure air hose to prevent falls from bystanders accidentally pulling on it. 6.
Vibration Precautions Safety This tool vibrates during use. Repeated or long‑term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use.
Functional Description 70 – 110 PSI Maximum Air Pressure 110 PSI Air Inlet 1/4" – 18 NPT Average Air Consumption 0.3 CFM @ 90 PSI Safety Mechanism Type Single Sequential Staple Type 20 Gauge, 1/4" – 5/8" Long, wide standard crown staples. Maintenance Operation Setup Operating Air Pressure Safety Specifications 61619 For technical questions, please call 1-800-444-3353.
Components and Controls Safety Air Deflector Trigger Air Inlet Setup Magazine Release Safety Nosepiece Driver Guide Magazine Safety Nosepiece - Also called the ″workpiece contact,″ the Safety Nosepiece helps prevent the tool from firing unless it is pressed against an object. Operation Maintenance Page 8 For technical questions, please call 1-800-444-3353.
Initial Tool Set Up/Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Air Supply TO PREVENT EXPLOSION: Use only clean, dry, regulated, compressed air to power this tool.
Description Non-lubricated Tools A Air Hose Filter Regulator Lubricator (optional) Coupler and Plug Leader Hose (optional) Air Cleaner / Dryer (optional) Air Adjusting Valve (optional) Maintenance A B C D E F G H Operation Lubricated Tools C Setup B B C A Function A E E F H Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapo
61619 For technical questions, please call 1-800-444-3353.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use tool until repaired. Workpiece and Work Area Set Up 1. Designate a work area that is clean and well‑lit. The work area must not allow access by children or pets to prevent distraction and injury. 2.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the trigger. • Detach the air supply. • Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners. 4. Keep fingers clear while sliding the Magazine closed until it clicks shut.
User-Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. Safety TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE ANY MAINTENANCE OR REPAIRS ARE DONE (including clearing jams): • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved impact safety goggles with side shields. • Release the trigger. • Detach the air supply.
If a fastener is jammed in the discharge area: If a fastener is jammed in the Magazine: 1. Disconnect Tool from air hose, press down on the Magazine Release (35) to open the Magazine. Open the Magazine completely. 1. Press down on the Magazine Release to open the Magazine. Open the Magazine completely. 3. Remove Screws (2) holding the Driver Guide Cover (43) in place. Lift the Driver Guide Cover up off the Driver Guide (47) and remove the jammed fasteners. 4.
Troubleshooting Problem Insufficient fastener depth. Possible Causes 1. Incorrect tool depth setting. 2. Not enough air pressure. Safety 3. Incorrect lubrication or not enough lubrication. 4. Blocked air inlet screen (if equipped). 5. Mechanism contaminated. Likely Solutions 1. Adjust depth setting, if available. 2. Check for loose connections and make sure that air supply is providing enough air pressure (PSI) to the tool’s air inlet. Do not exceed the Tool′s maximum air pressure of 110 PSI. 3.
Parts List and Diagram Maintenance Operation Setup THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Parts List Part Safety Setup Operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 Description Air Deflector Screw 4x18 Washer Cylinder Cap Air Seal O-Ring 11.8x2.4 Spring Washer Firing Valve Piston Piston Stopper O-Ring 26.6x2.4 O-Ring 21.3x3 Collar O-Ring 35x2 Cylinder Bumper Gasket E-Ring 5.5x2 Body Nozzle Air Seal Upper Remote Housing Remote Core O-Ring 3.5x1.6 Remote Housing O-Ring 9.8x1.9 Spring Releasing Blade Trigger Spring Pin 2.
61619 22 27 28 29 39 18 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
