Table of Contents Safetye��������������������������������������������������������� 2 Maintenancei���������������������������������������������� 10 Specifications.............................................. 6 Parts List and Diagram............................... 11 Setup........................................................... 7 Warranty.....................................................
. Avoid unintentional starting. Be sure the switch is off before connecting to the air supply. Do not carry the tool with your finger on the switch or connect the tool to the air supply with the switch on. 5. Use safety equipment. A dust mask, non-skid safety shoes and a hard hat must be used for the applicable conditions. 6. Always wear eye protection. Wear ANSI-approved safety goggles. 7. Always wear hearing protection when using the tool.
Air Source 1. Safety Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. 2.
Silicosis and Aluminum Oxide Warnings NIOSH recommends the following measures to reduce crystalline silica exposures in the workplace and prevent silicosis and silicosis-related deaths: 1. Prohibit silica sand (or other substances containing more than 1% crystalline silica) as an abrasive blasting material and substitute less hazardous materials. 2. Conduct air monitoring to measure worker exposures. 4. Practice good personal hygiene to avoid unnecessary exposure to silica dust. 5.
Functional Description Specifications Safety ITEM 60801 Maximum Air Pressure 60802 90 PSI Air Inlet 1/4″ -18 NPT Average Air Consumption Abrasive Capacity Abrasive Type 8.5 CFM @ 90 PSI 7 CFM @ 90 PSI 40 lb. 15 lb. Sodium Bicarbonate media only Components and Controls Media Valve Setup Safety Valve Media Regulator Knob Operation Tank Air Regulator Knob Air Valve Pressure Gauge Maintenance Nozzle Page 6 For technical questions, please call 1-800-444-3353.
Initial Soda Blaster Set Up/Assembly Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Assembly 1. Wrap the threads of the Pressure Gauge (7) with thread sealer tape (not included).
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Safety Inspect Soda Blaster before use, looking for damaged, loose, and missing parts. If any problems are found, do not use Soda Blaster until repaired.
Workpiece and Work Area Set Up 2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the air hose to possible damage. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 3. Secure loose workpieces using a vise or clamps (not included) to prevent movement while working. 4.
User‑Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. Safety TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the Soda Blaster, detach the air supply, safely discharge any residual air pressure in the Soda Blaster, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures.
Parts List and Diagram THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
