Table of Contents Safety ......................................................... 2 Maintenance ............................................... 7 Specifications ............................................. 5 Parts List and Diagram .............................. 10 Operation .................................................... 6 Warranty .................................................... 12 SAFETY WARNING SYMBOLS AND DEFINITIONS SETUP This is the safety alert symbol.
IMPORTANT SAFETY INFORMATION WARNING Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
Air Compressor Safety Warnings SAFETY 1. Risk of fire or explosion - do not spray flammable liquid in a confined area or towards a hot surface. Spray area must be well-ventilated. Do not smoke while spraying or spray where spark or flame is present. Arcing parts - keep compressor at least 20 feet away from explosive vapors, such as when spraying with a spray gun. 2. Risk of bursting - do not adjust regulator higher than marked maximum pressure of attachment. 3.
Specifications SAFETY Electrical Rating 12 VDC Maximum Air Pressure 150 PSI Air Flow Capacity 1.5 CFM Components and Controls End of Unit Compressor Hose On/Off Switch (on end of unit) SETUP On/Of Switch Clamps Air Hose Fuse Air Nozzle Grip Pressure Gauge Nozzles MAINTENANCE OPERATION Figure A Item 61745 For technical questions, please call 1-800-444-3353.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETY Compressor Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent injury. 2. Position the Compressor on a flat level surface.
Maintenance and Servicing SAFETY Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch “OFF” and disconnect the Battery Clamps before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM COMPRESSOR FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Troubleshooting Problem Possible Causes SAFETY Decreased output. 1. Not enough air pressure and/or air flow. 2. Blocked air inlet Filter (3). 3. Air leaking from loose housing or connections. 4. Mechanism contaminated. Severe air leakage. 1. Cross-threaded housing (Slight air leakage components. is normal, especially on 2. Loose housing. older tools.) No output SETUP 3. Dirty, worn or damaged valve. 1. Poor clamp connection. 2. Power Switch in Off (O) position. 3. Run-down battery. 4. Blown Fuse.
MAINTENANCE OPERATION SETUP THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Parts List and Diagram Parts List SAFETY Part SETUP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Description Cylinder Head Screw M4x12 Cylinder Head Cover Screw Arbor M5x50 Cylinder Cover O Ring Outlet Plate Assembly Radiator Cylinder Sleeve Screw M5x12 Carrier Ring Iron Bracket Outlet Pipe Handle Iron Bracket Compressor Hose Big Air Nozzle Small Air Nozzle Needle Fuse Gauge Air Hose Filter Screw M4x8 Front Cover Snap Ring Ø12 Shaft Qty 1 1 4 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1
OPERATION Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. MAINTENANCE SETUP SAFETY Assembly Diagram Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Page 11 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
