Specifications Weight Capacity 1,000 lb. Assembled Dimensions 34-3/4″ L x 31″ W x 36″ H Face Plate 10-3/16″ W x 6″ H x 7/16″ thick Wheel Diameter 3″ (x2), 3-1/2″ (x2) Important Safety Information Assembly Precautions 1. Assemble only according to these instructions. Improper assembly can create hazards. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. 3. Keep assembly area clean and well lit. 4. Keep bystanders out of the area during assembly. 5.
Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Middle Beam (20) Front Beam (11) Nut (14) Washer (13) Column (5) Rear Beam (23) Middle Beam (20) a Bolt (12) Figure B: Attach Front Beam b Lock Washer (21) Bolt (22) Figure A: Attaching Column to Rear and Middle Beams 1. To attach the Column to the Rear and Middle Beams: a.
Pin (4) Cotter Pin (3) Handle Grip (1) Mounting Arm (9) Column (5) Figure D: Attach Mounting Plate and Handle 5. Insert Mounting Plate (8) shaft into the top of the Column (5). Insert the Handle (2) through the Mounting Plate (8) and secure with the Cotter Pin (3). Washer (7) Mounting Plate (8) Handle (2) Mounting Plate (8) Nut (6) Bolt (10) Column (5) Figure E: Installing Arms and Locking Rotation 6.
Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this document including all text under subheadings therein before set up or use of this product. Mounting Engine TO PREVENT SERIOUS INJURY: Before attaching an engine to the stand, confirm that its weight does not exceed the Stand maximum capacity. 1. Remove the Pin (4) from the Column (5). 5. Tighten the Bolts (10) and Nuts (6) that hold the Mounting Arms (9) to 2.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM STAND FAILURE: Do not use damaged equipment. Make sure the stand is stable. If any unsafe conditions are found, take it to a qualified technician for service or repair. 1. BEFORE EACH USE, inspect the general condition of the Stand.
Parts List and Diagram Part 1 2 3 4 5 6 7 8 9 Description Handle Grip Handle Cotter Pin Pin Column Nut M12 Washer 12 Mounting Plate Mounting Arm Qty Part 1 1 1 1 1 4 4 1 4 10 11 12 13 14 15 16 17 18 Description Qty Bolt M12x45 Front Beam Bolt M10x70 Washer 10 Nut M10 Bolt M8x20 Washer 8 Lock Washer 8 Nut M8 4 1 2 2 2 8 8 8 8 Part 19 20 21 22 23 24 25 26 Description Qty 3″ Caster Middle Beam Lock Washer 12 Bolt M12x80 Rear Beam Wheel Washer 14 Snap Ring 14 3 2 1 1 1 1 2 2 2 2 1 4 5 7 6 8
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS DOCUMENT AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
