Specifications Capacity 1,000 lb. combined, 500 lb. individually (Static Conditions)* Max. Tailgate Height 42″ Dimensions 84″ L x 10″ W x 21/4″ H Important Safety Information 1. Before use: 5. Use as intended only. Do not use: a. Read and understand manual. a. as ladder, b. Inspect before every use; do not use if parts loose or damaged. b. to load/unload 3-wheeled vehicles, c. Turn vehicle’s ignition OFF and set parking brake. d.
11. All persons not involved in the loading process must stand clear of the loading ramps. Keep children away. Children must not be allowed in the work area. 12. Do not exceed tailgate capacity. 13. Avoid working alone. If an accident happens, an assistant can bring help. 14. Keep work area clean and well lit. Cluttered and dark areas invite injuries. 15. Store idle equipment. When not in use, store ramps in a dry location to inhibit rust. 21. Check for damaged parts.
Assembly Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 10. TOP 1. Line up the four holes on the Tongue (2) with the four holes on the Ramp (1).
Setup and Operation Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY: Before loading or unloading turn vehicle’s engine off, set its transmission in gear or park, engage its emergency brake and block its wheels. Make sure the Ramps are clean and dry before loading or unloading. Setup 1.
4- Wheel ATV Loading and Unloading • These ramps are for use with 2-wheeled dirt bikes and 4-wheeled ATV’s only. Do not use these ramps to load/unload 3-wheeled vehicles. • Do not use these ramps to load or unload any vehicle that weighs more than 1000 lb. • Do not use these ramps to load or unload any vehicle that is wider than the ramp. • Do not use these ramps to load or unload any vehicle that is carrying gear on its racks.
Expert Loading Directions Only for individuals certified by the ASI (ATV Safety Institute) By using directions in this section, you are agreeing that you are an ASI trained, certified rider and that you understand that your safety in performing this procedure is based on your ability to control the vehicle. 1. Have an assistant monitor the Ramp tongues for slippage on the tailgate. WARNING! Be sure the 4-wheeled ATV is centered on ramps. 2.
2-Wheel Bike Loading 1. Do not attempt to load any dirt bike or other 2-wheel motor bike alone. Have a qualified adult assist. 2. Line up the 2-wheel bike with one of the Ramps. 3. With one person pushing the bike slowly up the Ramp, a helper should be in the bed of the hauling vehicle both to guide and to apply the brake if it is necessary to stop the bike while it is on the ramp. Have one person with a hand on the bike hand brake for safety. 4.
Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY: Remove the ramps from the vehicle before performing any maintenance or service. Do not use damaged equipment. If Ramps are damaged, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the Ramps. Check for: 2. Clean the ramps after each use.
Parts List and Diagram PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
Assembly Diagram Bolt (3) Tongue (2) Ramp (1) Washer (6) Lock Washer (4) Nut (5) ITEM 60397 Attach Safety Chain to one of the holes on the side of the ramp using an M6 x20 Bolt and M6 Lock Nut (all sold separately). For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
