Table of contents Safety ......................................................... 2 Maintenance .............................................. 12 Specifications ............................................. 9 Parts List and Diagram .............................. 14 Setup .......................................................... 9 Warranty .................................................... 16 SAFETy Operation ...................................................
1. power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 2.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
18. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform . Holding the work by hand or against your body is unstable and may lead to loss of control and personal injury. 19. This product is not a toy. Keep it out of reach of children. 20. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
Safety Warnings Specific for polishing Operations Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece. SAFETy Vibration Safety This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders.
TO pREVENT ELEcTRIc SHOcK AND DEATH FROM INcORREcT GROUNDING WIRE cONNEcTION: check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
Extension cords 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. SAFETy 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Table A.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord.
Electrical Rating 120V~ / 60Hz / 1A No Load Speed 3,000 OPM Max. Accessory Diameter 10″ 14pU E242023 Setup - Before Use: SAFETy Specifications Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.
Operating Instructions Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. SAFETy Workpiece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. SETUp 2.
polishing Instructions 3. Apply about two tablespoons of wax (not included) evenly on the clean Foam Pad. NOTIcE: Do not apply the wax directly to the surface of the vehicle. The amount of wax needed will vary according to the size of the vehicle being waxed. NOTIcE: Only use slower speeds for polishing. Otherwise, damage may occur to the paint being polished. Harbor Freight Tools is not responsible for damage to the vehicle’s finish due to improper use of this tool. 4.
Maintenance and Servicing procedures not specifically explained in this manual must be performed only by a qualified technician. SAFETy TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Make sure that the power Switch/Trigger is in the off-position and unplug the tool from its electrical outlet before performing any procedure in this section. TO pREVENT SERIOUS INJURy FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Troubleshooting Performance decreases over time. Excessive noise or rattling. Overheating. Tool does not polish effectively. Carbon brushes worn or damaged. SAFETy 3. Internal damage or wear. (Carbon brushes or switch, for example.) Tool operates slowly. 1. Excess pressure applied to workpiece. 2. Power being reduced by long or small diameter extension cord. Likely Solutions 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker.
parts List and Diagram pLEASE READ THE FOLLOWING cAREFULLy SAFETy THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
MAINTENANcE OpERATION SETUp SAFETy Assembly Diagram Item 61420 For technical questions, please call 1-800-444-3353.
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
