User's Manual
16_ live
live
Name Description
System
Operation
RAID
It is displayed when you cannot write RAID due to a malfunction of HDD.
It is displayed when the max permitted amount of data for each channel is exceeded.
It is displayed when the network is overloaded.
` It occurs when the max receiving allowance is exceeded, causing an overload to the
CPU. It will disappear if you modify the camera settings or delete a camera to reduce
the performance burden.
It is displayed when there is firmware to update the server.
/
Shows GPS reception/no reception.
Appears when emergency recording is in progress.
Shows the vehicle shake state.
/
Displays the Wi-Fi connection status when <Wi-Fi Enable> is set.
Video Input
Status
Displayed if no input is entered in the condition that the camera is set to <ON>.
Displayed when the live image with the camera turned <ON> exceeds the supported
resolution.
Displayed if no permission to live view is granted.
If a camera is <OFF>, or if no camera is registered, or it is in <Covert2> mode, nothing
will be displayed on the screen.
If the camera is set to <Covert1>, the video will be displayed but the OSD menus will not
be displayed.
Camera Title / Channel
Display the camera title and channel number.
Camera
Operation
This icon is displayed for a channel that a PTZ-featuring camera is connected to.
Displays AUDIO ON/MUTE. Not displayed in video mode if deactivated.
If the sensor is set to <ON>, the input signal will be displayed on the screen of the
connected channel.
This icon is displayed when Motion Detection is set to <ON> and a camera motion or
camera event occurs.
It displays the status of general/event/scheduled recording.
It is displayed when it fails to decode all the frames due to limited decoding performance
and in this case only the I-Frame is decoded.
RED - Displayed when there is any abnormality in the RED-SD card.
YELLOW - Displayed when there is no storage space in the SD card.
Flickers when a defocus event occurs. When you click the icon, a simple focus command
is sent to the camera.
Error Information
• If the built-in HDD is not connected, the “NO HDD” icon ( ) will be displayed in the top left corner. In this
case, the recording, playback and backup functions do not work. If a new HDD is installed, format the HDD
using the "Device > Storage Device" menu.
M
` If you see the icon for NO HDD ( ) or HDD FAIL (
FULL NO
RAID
RAID
SCSI
) after HDD formatting, be sure to contact
your service center.
Live Screen Menu
If you right click with your mouse button in live screen mode, it will launch the live screen menu where you can
access each menu.
The context menu differs depending on the state of Log in/out, split mode, and NVR operation status.
M
` Depending on the user permissions, you may have limited access to menu items of Live View, Backup, Stop Recording,
Search, PTZ, Remote Alarm Output, and Exit.
Single Mode Menu
The single mode menu is available only in Single Mode.
If the menu is displayed as <Screen Mode> in the single screen, it is displayed as a <Full Screen> in the
menu where only one channel is selected in the split screen.
Menu Description
Full Screen
Select and click a desired channel in Split mode to switch to the full screen of the selected
channel.
b
PTZ Control
Accesses the PTZ Control menu. The PTZ menu will be active on the Live screen after you
select a single channel.
(Page 23)
c
ZOOM You can enlarge the selected screen. (Page 21)
Capture Captures the screen of the selected channel. (Page 22)
Scene Mode ►
Layout ►
Keep ch. scr ratio
Status ►
PTZ Control
ZOOM
Audio ►
Freeze
Stop Alarm
Capture
Record Stop
Play
Search
Backup
Menu
Shutdown
Logout
Hide Launcher
< Single Mode Menu >
Full Screen
Layout ►
Keep ch. scr ratio
Status ►
PTZ Control
ZOOM
Audio ►
Freeze
Stop Alarm
Capture
Record Stop
Play
Search
Backup
Menu
Shutdown
Logout
Hide Launcher
< One channel selection menu in the split screen >
b
c