RFID Reader User Manual SSA-R2001V
RFID Reader User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING • To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. WARNING 1.
safety information FCC Statement Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation.
contents PRODUCT INTRODUCTION 6 9 INITIALIZATION Features What’s included At a Glance Cable Color Scheme Cable Selection 9 10 11 Installation Precautions on installation External Connection 12 Basic Operations 13 14 15 WIEGAND Output RS-232 Output 8 Bit Burst Output Format 16 Troubleshooting 17 Product Specifications 12 OUTPUT FORMAT 13 TROUBLESHOOTING 16 PRODUCT SPECIFICATIONS 17 English English _ 5 CONTENTS INSTALLATION AND EXTERNAL CONNECTION 6 6 7 8 8
product introduction FEATURES This model is an elegant-looking proximity reader that is featured by the capacitive touch-sensing keypad. The back-lighted keypad is useful especially for night operation, and its epoxy adhesion and aluminium case relieve you of worries about the rain or any other challenging weather conditions. This model permits user access through authentication of the presented proximity card and personal identification number using the keypad.
AT A GLANCE Front/Rear 4 5 SSA-R2001V 6 1 LED Displays the status of the system operation. 2 Keypad Used to enter the ID/password. 3 Tamper Switch A tamper switch to detect falling from the wall. 4 Connection Cable Used to connect to the power source or I/O cable. 5 Buzzer Piezo buzzer. 6 Fixing Hole Fixing hole for wall-mounting.
product introduction CABLE COLOR SCHEME Name of I/O Pin Signal Line Cable Color Power (+12V) DC +12V Red Power Ground GND(-) Black Wiegand Data Output 0 WIK_DATA0 Green Wiegand Data Output 1 WIK_DATA1 White Not used. Not used. Orange RS-232 TX TX OUT Purple Not used. Not used.
installation and external connection INSTALLATION 1. See [Figure 1] to drill 6-32” holes and 1/2” holes (totally 4) into the wall. 2. Tighten the four screws to secure the product to the wall. 60.30 79.60 4cm 100.80 00 91.50 4.35cm 6-32 or M3 Screws 8.7cm Ø1. 86.50 1/2˝ hole 4.35cm 12.50 50 6-32 hole 69.10 54.50 6.4cm Ø1. 72.50 36.50 26.23 Reader Module Ø1.50 SSA-R2001V 18.50 Bezel 6.00 0.00 [Figure 1] 80.60 72.30 49.30 56.30 62.30 18.30 31.30 64.00 0.00 7.80 8.30 81.
installation and external connection PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall, the read range may be reduced. To avoid this problem, it is recommended to insert the spacer between the metal wall and the reader as shown below. Metal Wall Spacer 2001V SSA-R Reader IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than one reader side by side or front and back, the read range may be reduced.
EXTERNAL CONNECTION WIRING DIAGRAM White Wiegand Data 1 Out Tamper Switch Out(NC) Light yellow Tamper Switch Out(COM) CONTROLLER Buzzer Control In RS-232(TX) Purple Pink PC Blue RS-232(GND) Black LED Control In(Green) Yellow LED Control In(Orange) Gray SSA-R2001V Red Black DC +12V GND POWER Category Cable Wiring Connect the DC+12V to the red line. Power Supply Unit Connect GND to the black line. Connect the green line of the product to the Wiegand D0 input port of the controller.
initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep five times before entering Standby with the red indicator turned on. Using the card C ar d X Y [ Z \ ^ ] i _ lzj ` W lzj zzhTzYWWW Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller.
output format WIEGAND OUTPUT Timing Diagram 5V 1ms DATA-0 0V 5V DATA-1 LOGIC 1 2 3 n-2 n-1 0 1 1 1 0 0V n *n : 34 or26 0 Data Format (34-bit) • Bit 1 : Even Parity (bit 2 ~ bit 17) • Bit 2~Bit33 : 4-byte ID Number • Bit 34 : Odd Parity (bit 18 ~ bit 33) English English _ 13 OUTPUT FORMAT 100us
output format RS-232 OUTPUT Output Waveform LSB +15V 0 1 MSB 0 0 0 0 0 1 0 Space(=0) +3V Indeterminate Region 0V -3V Mark(=1) 8 Data Bits -15V 2 Stop Bits Start Bit Data packet corresponding to ASCII character ‘A’ Data Type M START (0X02H) DATA (10 Char) END (0x03H) LRC START(0X02H) DATA (10 Char) END (0x03H) LRC Check the following settings: Baud Rate : 9600bps Data Bit : 8 Parity Bit : None Stop Bit : 1 LRC : This is the result of XOR operation of each byte from Start to
8 BIT BURST OUTPUT FORMAT 8Bit Burst Output Format Binary Hexa Keypads Binary Hexa 0 11110000 F0 6 10010110 96 1 11100001 E1 7 10000111 87 2 11010010 D2 8 01111000 78 3 11000011 C3 9 01101001 69 4 10110100 B4 ESC 01011010 5A 5 10100101 A5 ENT 01001011 4B English English _ 15 OUTPUT FORMAT Keypads
troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. PROBLEM SOLUTION My card is not read properly. 1) 2) Check the rated voltage specified in the user manual and the catalog. Ensure that you are using an ISO14443 Type A card. - Cards of 125 kHz format can not be used. However, the 13.56 MHz card can not be used if it is of Type B, ISO15693. (Contact the card retailer regarding the card format.
product specifications PRODUCT SPECIFICATIONS Item SSA-R2001V Power / Current DC 12V / Max.
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungsecurity.com www.samsungtechwin.com SAMSUNG TECHWIN EUROPE LTD.
