User's Manual
English ·
7
Button Description
No. Icon Name Description
n
View Mode
Select camera(s) to view and the viewing
mode.
o
Brightness
/ Volume
Adjustment
Adjust monitor brighness level: 1~5.
Adjust monitor volume level: mute, 1~7.
Adjust camera volume level: 1~5.
p
Temperature
Temperature display On/OFF, and set
temperature.
q
VOX/ECO
Sensitivity
Adjust VOX/ECO Sensitivity Level: Low or
high sensitivity.
r
Feed Timer
Turn ON/OFF to display the baby feed
timer.
Set baby's feeding schedule.
s
Pairing Pair/Unpair 1-4 Cameras.
t
System Menu
Set time and flip mode, or reset the
monitor to factory settings.
Function Description
VOX (Voice activated)
Select to monitor and listen for significant sound levels with reduced
ambient noise.
The monitor screen goes off in "VOX" mode after 30 seconds if there is no
detection of significant sounds louder than the minimum noise level, but
turns back on as soon as it detects sound that exceeds the minimum noise
level.
You can set the sensitivity level in "VOX" mode.
• 'Low' Sound Level Detection : Sets to higher sensitivity.
• 'High' Sound Level Detection : Sets to lower sensitivity.
ECO Mode
In the energy-saving ECO mode, the screen goes off after 30 seconds if
there is no detection of significant sounds louder than the minimum noise
level. The monitor will not deliver any detected background sounds once
the camera goes into this power saving mode, which helps decrease the
RF radiation levels in the baby's environment. The monitor screen turns
back on as soon as the camera detects sound exceeding the minimum
noise level.
Video Mode
The screen is always in "Video" mode for continuous video and audio
monitoring.
Audio Mode
The screen will turn off in "Audio" mode to only capture sounds around the
camera(s) surrounding. The screen will turn back on by pressing any button
on the monitor.
No Signal Warnings
An "Out of Range" message will appear when the baby monitor is out of the
camera's range.
To improve the wireless signal strength, reposition the camera and/or the
monitor closer to each other, or check the camera's power connection.
Sequence View
Select View Menu to enter into Sequence View. The sequence will start at
Cam 1, then automatically switch to the next camera, Cam 2, after
10-seconds. When enabled, "Sequence View" will continue to change
between cameras. To see details from a particular camera's view, just press
the "OK" button to display the camera's view in full screen.
Monitor
` Mode button:
Press to change between modes (VOX - ECO - VIDEO -
AUDIO).
Mode Selection: select the desired mode, then the monitor will switch to the
chosen mode.
` Power button: 1) Press and hold down for 2-3 seconds to turn ON/OFF
the monitor. 2) When in On-Screen Display (OSD) mode, press the
power button briefly to return to the previous interface.
` Lullaby button: Shows a list of Lullabies (#1-4: Lullabies, #5-7 White
Noise, ALL: all Lullabies from #1-4).
1) Select a lullaby from the list to play and press "OK". 2) Press "OK"
again to stop playing the lullaby, and press the "Lullaby" button to exit
out of the lullaby list.
` Talk button: Press and hold button to speak.
` OK button: 1) Press to display menu or confirm selection. 2) When in
View Mode, the camera will zoom in and out sequentially each time you
press and hold the "OK" button.
` Direction button: 1) Press left or right button to adjust the camera's
framing to the left or right, and press the up or down button to adjust
the camera's framing upwards or downwards. 2) When in View mode,
press the left and right button to adjust the monitor's brightness, and
press up and down to adjust the monitor's volume.
Camera
` Reset button: Press the reset button for at least 3 seconds to reset the
camera.
` Power switch: Turn ON/OFF the camera.
` Pair button: Pair camera(s) to monitor.