User's Manual

rst time setup
Dynaudio Xeo 2
- Unpack the speakers.
- A pair of speakers consist of a Master
and a Slave unit. Master unit carries the
audio input interfaces. Choose the most
convenient position for the Master and
Slave unit.
- Set the left and right switch on rearplate for
each speaker.
- Set the speaker position switch that best
describes the speakers need for acoustic
compensation.
• Neutral the speaker has no
reecting walls nearby
• Wall the speaker is
positioned near a wall
• Corner the speaker is
positioned near two walls
- Speakers that should play together must
have same zone-setting (Red, Green, Blue).
Connect power cable to the speakers.
Apply power and await bootup.
Pairing is done by Press-and-hold the
button on remote. This will make the master
speaker available for pairing for one minute.
During this minute you can connect your
device to the master speaker. The pairing will
be stored in the speaker.
Connecting your device via Bluetooth
When your device has been paired with the
master speaker, you can connect again by
choosing the Xeo 2 device from your list of
Bluetooth devices.
To playback from Bluetooth input, pair and
connect your Bluetooth source device with
the speakers and start playback. Press
button on remote to choose this input on
the speakers.
Disconnecting your Bluetooth device
Press-and-hold button to disconnect
a connected device or disconnect from the
device connected to the speaker.
Playback from direct inputs
Apply signal to one or more of the audio
inputs of the master speaker and press
according button (AUX, LINE, OPT) on the
remote. The speakers will automatically
detect the signal and start playback. If they
are set to same zone, master and slave will
connect wirelessly with each other.
If no signal is applied to either input, the
speaker will keep on scanning the inputs for
the next 20 minutes and go to standby.
Press the remote button , or ,
corresponding to the Id setting on the
rearplate of the Hub/Connect.
When connection is established, you can
press the desired Input button on remote.
*Connect/Hub/remote control sold seperately.
button
- Press to power ON the speaker and scan
the inputs.
• If previous input was direct inputs, it will
scan the direct inputs for audio signal.
• If previous input was from Hub/Connect,
it will scan the previous devices inputs.
- Press to jump to another input.
- Press-and-hold to power OFF the speaker.
button
- Raises the volume level.
- Press-and-hold to do fast adjustment.
button
- Lowers the volume level.
- Press-and-hold to do fast adjustment.
Adjustments (example)
Speaker 1:
Master, Left, Corner, Red
Speaker 2:
Slave, Right, Wall, Red
Placement
Power to speaker
Bluetooth setup
Connect speakers
Playback from Dynaudio Hub
or Dynaudio Connect
Controls
1
2
3
4
5
6
Master
Speaker 1
Source
Slave
Speaker 2


White LED on the front of the speaker
indicates Bluetooth status
Pairing Mode
Connected
Not Connected
Aux In Line In
R L
Optical In Coax In USB In
PC/Mac
Sound Card
Bluetooth Setup
WiFi Setup
Id
A
B
C
Service
5V DC
2A
1 2 3 4
1 Basic setup
Dynaudio Connect
Start guide
Set the broadcast mode of Dynaudio Connect to
multiroom mode or hi-res mode. Note that Xeo
4/6 speakers do not support hi-res broadcast.
Speakers will need the latest firmware upgrade
to support 24 Bit / 96kHz broadcast.
When changing broadcast mode of Dynaudio
Connect, speakers will need to reboot by
disconnecting mains power to enable new
broadcast mode. Reboot can also be done by
press-and-hold A, B or C button on remote.
Set the Id switch on rearplate to A, B or C.
Connect your source(s) on the rearplate.
Connect power to the device. Wait 30 sec.
Connect power to your speakers.
Power ON speakers.
Select A, B or C on your remote control, make
sure it matches to your settings on the Dynaudio
Connect, either A, B or C.
Choose input 1-4 on the remote.
A
D
B
C
D
BEF
Rearplate and bottom
C
A
Not Connected
Connected
Pairing Mode
Bluetooth
High Resolution
1 Zone
24 Bit / 96 kHz
Multiroom
3 Zones
16 Bit / 48 kHz
WiFi
Not Connected
Connected
Slow Blinking:
Acess Point Mode
Fast Blinking:
WPS Mode
Model: Dynaudio Connect, ID 4573141
Dynaudio A/S, Sverigesvej 15, DK-8660 Skanderborg
This device complies with Part 15 of the FCC Rules.
Its operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Contains FCC ID:XCO-HSDWAM83
IC:7756A-HSDWAM83
A B
1
2
3
4
C
Important! Make sure you have the latest firmware update. Visit dynaudio.com/support
Find latest manuel on dynaudio.com/support
Remote
3 Bluetooth setup
Bluetooth pairing is done by pressing the Bluetooth button on the rearplate
and connecting your Bluetooth device within 1 min.
If a user wants to establish a connection while another user is already
connected, you can force-disconnect the user by pressing the ( E ) button on
the rearpanel of the Dynaudio Connect.
Status indicator:
E
2 WiFi-setup
Find Dynaudio Connect in
your list of WiFi devices
and connect to it.
2
Please go to the website:
http://192.168.1.1 and
follow the setup wizard to
connect to your home
network.
3
Press-and-hold the WiFi
setup button for 3
seconds to make the
Dynaudio Connect
searchable from an external
device (the WiFi light on the
front starts blinking slowly).
1
F
Optical In Coax In USB In
PC/Mac
Sound Card
Bluetooth Setup
WiFi Setup
Id
A
B
C
Service
5V DC
2A
3 4
F
(3 sec.)
WiFi-setup
Dynaudio Connect | A
192.168.1.1
Network configuration
Connection Status:
Wireless LAN Settings
Dynaudio Connect | A
Mac Adress:
CC:90:93:05:2A:6C
Airplay Device Name:
Service Set ID (SSID)
Dynaudio Connect | A
2,4GHzCisco00589(NONE)
Apply
Advanced Settings
Not Connected
Status indicator:
Connected Slow Blinking: Acess Point Mode
Fast Blinking: WPS Mode When playing via WiFi - select channel 4 on your remote
Not Connected
Connected Pairing Mode
When playing via Bluetooth - select channel 4 on your remote
*
**
C
M
Y
CM
MY
CY
CMY
K
Start_Guide_Dynaudio_Connect.pdf 3 18/05/15 09.33
Aux In Line In
R L
Optical In Coax In USB In
PC/Mac
Sound Card
Bluetooth Setup
WiFi Setup
Id
A
B
C
Service
5V DC
2A
1 2 3 4
1 Basic setup
Dynaudio Connect
Start guide
Set the broadcast mode of Dynaudio Connect to
multiroom mode or hi-res mode. Note that Xeo
4/6 speakers do not support hi-res broadcast.
Speakers will need the latest firmware upgrade
to support 24 Bit / 96kHz broadcast.
When changing broadcast mode of Dynaudio
Connect, speakers will need to reboot by
disconnecting mains power to enable new
broadcast mode. Reboot can also be done by
press-and-hold A, B or C button on remote.
Set the Id switch on rearplate to A, B or C.
Connect your source(s) on the rearplate.
Connect power to the device. Wait 30 sec.
Connect power to your speakers.
Power ON speakers.
Select A, B or C on your remote control, make
sure it matches to your settings on the Dynaudio
Connect, either A, B or C.
Choose input 1-4 on the remote.
A
D
B
C
D
BEF
Rearplate and bottom
C
A
Not Connected
Connected
Pairing Mode
Bluetooth
High Resolution
1 Zone
24 Bit / 96 kHz
Multiroom
3 Zones
16 Bit / 48 kHz
WiFi
Not Connected
Connected
Slow Blinking:
Acess Point Mode
Fast Blinking:
WPS Mode
Model: Dynaudio Connect, ID 4573141
Dynaudio A/S, Sverigesvej 15, DK-8660 Skanderborg
This device complies with Part 15 of the FCC Rules.
Its operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Contains FCC ID:XCO-HSDWAM83
IC:7756A-HSDWAM83
A B
1
2
3
4
C
Important! Make sure you have the latest firmware update. Visit dynaudio.com/support
Find latest manuel on dynaudio.com/support
Remote
3 Bluetooth setup
Bluetooth pairing is done by pressing the Bluetooth button on the rearplate
and connecting your Bluetooth device within 1 min.
If a user wants to establish a connection while another user is already
connected, you can force-disconnect the user by pressing the ( E ) button on
the rearpanel of the Dynaudio Connect.
Status indicator:
E
2 WiFi-setup
Find Dynaudio Connect in
your list of WiFi devices
and connect to it.
2
Please go to the website:
http://192.168.1.1 and
follow the setup wizard to
connect to your home
network.
3
Press-and-hold the WiFi
setup button for 3
seconds to make the
Dynaudio Connect
searchable from an external
device (the WiFi light on the
front starts blinking slowly).
1
F
Optical In Coax In USB In
PC/Mac
Sound Card
Bluetooth Setup
WiFi Setup
Id
A
B
C
Service
5V DC
2A
3 4
F
(3 sec.)
WiFi-setup
Dynaudio Connect | A
192.168.1.1
Network configuration
Connection Status:
Wireless LAN Settings
Dynaudio Connect | A
Mac Adress:
CC:90:93:05:2A:6C
Airplay Device Name:
Service Set ID (SSID)
Dynaudio Connect | A
2,4GHzCisco00589(NONE)
Apply
Advanced Settings
Not Connected
Status indicator:
Connected Slow Blinking: Acess Point Mode
Fast Blinking: WPS Mode When playing via WiFi - select channel 4 on your remote
Not Connected
Connected Pairing Mode
When playing via Bluetooth - select channel 4 on your remote
*
**
C
M
Y
CM
MY
CY
CMY
K
Start_Guide_Dynaudio_Connect.pdf 3 18/05/15 09.33
Aux In Line In
R L
Optical In Coax In USB In
PC/Mac
Sound Card
Bluetooth Setup
WiFi Setup
Id
A
B
C
Service
5V DC
2A
1 2 3 4
1 Basic setup
Dynaudio Connect
Start guide
Set the broadcast mode of Dynaudio Connect to
multiroom mode or hi-res mode. Note that Xeo
4/6 speakers do not support hi-res broadcast.
Speakers will need the latest firmware upgrade
to support 24 Bit / 96kHz broadcast.
When changing broadcast mode of Dynaudio
Connect, speakers will need to reboot by
disconnecting mains power to enable new
broadcast mode. Reboot can also be done by
press-and-hold A, B or C button on remote.
Set the Id switch on rearplate to A, B or C.
Connect your source(s) on the rearplate.
Connect power to the device. Wait 30 sec.
Connect power to your speakers.
Power ON speakers.
Select A, B or C on your remote control, make
sure it matches to your settings on the Dynaudio
Connect, either A, B or C.
Choose input 1-4 on the remote.
A
D
B
C
D
BEF
Rearplate and bottom
C
A
Not Connected
Connected
Pairing Mode
Bluetooth
High Resolution
1 Zone
24 Bit / 96 kHz
Multiroom
3 Zones
16 Bit / 48 kHz
WiFi
Not Connected
Connected
Slow Blinking:
Acess Point Mode
Fast Blinking:
WPS Mode
Model: Dynaudio Connect, ID 4573141
Dynaudio A/S, Sverigesvej 15, DK-8660 Skanderborg
This device complies with Part 15 of the FCC Rules.
Its operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
CAN ICES-3 (B)/NMB-3(B)
Contains FCC ID:XCO-HSDWAM83
IC:7756A-HSDWAM83
A B
1
2
3
4
C
Important! Make sure you have the latest firmware update. Visit dynaudio.com/support
Find latest manuel on dynaudio.com/support
Remote
3 Bluetooth setup
Bluetooth pairing is done by pressing the Bluetooth button on the rearplate
and connecting your Bluetooth device within 1 min.
If a user wants to establish a connection while another user is already
connected, you can force-disconnect the user by pressing the ( E ) button on
the rearpanel of the Dynaudio Connect.
Status indicator:
E
2 WiFi-setup
Find Dynaudio Connect in
your list of WiFi devices
and connect to it.
2
Please go to the website:
http://192.168.1.1 and
follow the setup wizard to
connect to your home
network.
3
Press-and-hold the WiFi
setup button for 3
seconds to make the
Dynaudio Connect
searchable from an external
device (the WiFi light on the
front starts blinking slowly).
1
F
Optical In Coax In USB In
PC/Mac
Sound Card
Bluetooth Setup
WiFi Setup
Id
A
B
C
Service
5V DC
2A
3 4
F
(3 sec.)
WiFi-setup
Dynaudio Connect | A
192.168.1.1
Network configuration
Connection Status:
Wireless LAN Settings
Dynaudio Connect | A
Mac Adress:
CC:90:93:05:2A:6C
Airplay Device Name:
Service Set ID (SSID)
Dynaudio Connect | A
2,4GHzCisco00589(NONE)
Apply
Advanced Settings
Not Connected
Status indicator:
Connected Slow Blinking: Acess Point Mode
Fast Blinking: WPS Mode When playing via WiFi - select channel 4 on your remote
Not Connected
Connected Pairing Mode
When playing via Bluetooth - select channel 4 on your remote
*
**
C
M
Y
CM
MY
CY
CMY
K
Start_Guide_Dynaudio_Connect.pdf 3 18/05/15 09.33
Sources
Line In Optical In AUX In Bluetooth
Master
Speaker
Connect/
Hub*
Controls on the top
of the speaker
Remote
Control
Remote
Control*
–
+
+
DIRECT
In
VOLUME
DIRECT
In
VOLUME
DIRECT
In
VOLUME
–
Subject to change without notice.
Please nd the latest manual and rmware version on www.dynaudio.com
Red