User's Manual

ManualsBrandsHansong Technology ManualsElectronicsLS6-N22S-M (Network Media Module)

USER Manual

LS6-N22S-M

SPECIFICATIONS

1.power up for MT7620A with battery 7.4V

2.Connect to the PC with RS232.

3.run the CMD on PC

4.run the MT7620A's QA tools which given by the supplier.

5. The MT7620 router module with two antenna ports which

pattern is MOMI,the two antenna are the same one.

The antenna manufacturer A:Suzhou point positive electronic

technology co.,ltd

Model No:RC8WFI0063A or Model No:FCIWF10779A

Ant. Gain: Ref Ant. spec

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to

operate the equipment.

Summary of content (10 pages)

PAGE 1
USER Manual LS6-N22S-M SPECIFICATIONS 1.power up for MT7620A with battery 7.4V 2.Connect to the PC with RS232. 3.run the CMD on PC 4.run the MT7620A's QA tools which given by the supplier. 5. The MT7620 router module with two antenna ports which pattern is MOMI,the two antenna are the same one. The antenna manufacturer A:Suzhou point positive electronic technology co.,ltd Model No:RC8WFI0063A or Model No:FCIWF10779A Ant. Gain: Ref Ant. spec FCC Statement This device complies with part 15 of the FCC Rules.
PAGE 2
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 3
transmitters is forbidden. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.
PAGE 4
The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Information for the OEM Integrators This device is intended for OEM integrators only. Please see the full grant of equipment document for restrictions.
PAGE 5
LS6-N22S 1. Introduction Libre LS6-N22S is a complete network media module. It includes an 802.11n MAC and baseband, a 2.4 GHz 2x2 MIMI radio and FEM, a 580MHz MIPS® 24K™ CPU core, with supporting FLASH and DRAM memory. The module also includes all the necessary I/O and control interfaces required to build feature rich networked media products, yet cost effective with very little additional electronic design.
PAGE 6
LS6-N22S  Green AP  Intelligent Clock Scaling (exclusive)  DDR2: ODT off, Self-refresh mode  I2C, I2S, SPI, UART, JTAG, GPIO  I2S interface supports 16-bit/96kHz (slave mode)  Hardware NAT with IPv6  WEP64/128, TKIP, AES, WPA, WPA2, WAPI  QoS: WMM, WMM-PS  WPS: PBC, PIN 3. LibreSync Features LibreSync modules have extensive software features for connected media streaming and control applications.
PAGE 7
LS6-N22S 4. Block Diagram Figure 4-1: LS6-N22S Block Diagram 5. Specifications 5.1. General Specification Parameter Description / Values Model LS6-N22S Product Name LibreSync LS6 Network Media Module Chipset MT7620A Standard Wi-Fi – IEEE802.11b, IEEE802.11g, IEEE802.11n, standards Libre Wireless Technologies Data Sheet: Network Media Module, Ver. 3.
PAGE 8
LS6-N22S Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120, and maximum of physical layer rate of 130Mbps Frequency Band 2.4 GHz Input Voltage 3.3 V ± 5 % Operating Temperature -20˚C to + 55˚C Dimensions 40mm X 26mm X 5.1mm (L x W x H) ± 0.2mm 5.2. Wi-Fi Specification Parameter Standard Data Rate Modulation Network Architecture Operation Channel Frequency Range Libre Wireless Technologies Description / Values IEEE802.11b, IEEE802.11g, IEEE802.11n standards  802.
PAGE 9
LS6-N22S Transmit Output Power Receiver Sensitivity Security  802.11b : < 19.5 dBm at 11Mbps  802.11g : < 16.5 dBm at 54Mbps  802.11n : < 15.5 dBm at MCS7  802.11b : -84 dBm at 11Mbps  802.11g : -73 dBm at 54 Mbps  802.11n : -64 dBm at 130 Mbps (MCS7) WEP 64&128 bit, WPA, WPA-PSK, WPA2, WPA2-PSK, WPS, IEEE 802.1x, IEEE 802.11i Current Consumption  TX Mode : 420 mA  RX Mode : 220 mA 6. Mechanical, Connectors and Interfaces 6.1. Physical Module Estimated at 40mm x 26mm x 5.
PAGE 10
LS6-N22S  Dimensions are in millimetres  Dimensional tolerance is +/- 0.2mm  PCB thickness is 1mm  Design for 5.1mm physical Z height clearance (space for shields/clearance) Figure 6-2: LS6-N22S Top View With and Without Shield 6.2. Connector Specification Figure 6-3: LS6-N2SS Connector Specification Libre Wireless Technologies Data Sheet: Network Media Module, Ver. 3.