Installation Instructions / Warranty Citterio 39115XX1
�� �� �� Citterio Wall-Mount Lavatory Trim 39115XX1 ��� ��� Technical Data Maximum incoming water pressure 145 psi Recommended incoming pressure 14.5 - 72 psi Recommended hot water temperature 120oF - 140oF* Flow rate 2.2 gpm The hot and cold supplies must be of equal pressure for proper operation of the faucet. *Know and follow all applicable local codes when setting the temperature of the water heater.
Installation Instructions Turn off the water at the supply before beginning the installation. · Remove the caps from the plaster shields. Cut the plaster shields 1 mm (1/16”) from the surface of the finished wall. Seal around the plaster shields with a suitable, non-staining, waterproof bathroom sealant. · Use a 27 mm deep socket wrench to remove the flush insert. · Use a 17 mm deep socket wrench to remove the plug from the spout port.
· Install the springs and cup washers in the valve body. Install the cartridge assembly. · Install the handle. Tighten the set screw using the enclosed 2 mm allen wrench. · Measure the distance from the surface of the finished wall to the end of the handle.
If the distance is 3 1/4” – 3 7/8”, select the two “A” sleeves (1-1/4” long). If the distance is 3 7/8” – 4 3/8”, select the two “B” sleeves (7/8” long) If the distance is 4 3/8”, select the two “C” sleeves (1/2” long) · Screw the escutcheon retainers to the ends of the two sleeves.
· Measure the distance from the outside surface of the finished wall to the spout port (“X”). Add 2” to X · Measure the threaded end of the spout. Using proper tools and safety practices, cut the spout so that the threaded portion is X + 2” long. x + 2” · Wrap the threads on the spout connector with several layers of a good quality TeflonTM tape. Screw the spout connector into the rough. · Place the face plate against the wall.
· Use the service key to tighten the escutcheon retainers against the plate. · Lightly coat the threads on the flanges with the included lubricant. Screw the flanges onto the retainers. · Push the cap over the handle assembly. Push the spout over the connector and tighten the set screw.
User Instructions Lift the handle to turn the faucet on. Pivot the handle to the left for warmer water, to the right for cooler water. Push the handle down to turn the water off.
Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers · · · · To remove lime scale, use only products made specifically for that purpose.
Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
TO OBTAIN WARRANTY PARTS OR INFORMATION Contact your Hansgrohe retailer, or contact Technical Service at: Hansgrohe Inc. 1492 Bluegrass Lakes Parkway Alpharetta GA 30004 Toll-free (800) 334-0455. In requesting warranty service, you will need to provide 1. . 3. The sales receipt or other evidence of the date and place of purchase. A description of the problem. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc.
www.hansgrohe-USA.com US - Installation Instructions • Part No. 90575801 • Revised 4/2007 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.
