Installation Instructions / Warranty Axor Citterio 39143XX1 Axor Citterio 39147XX1
Axor Citterio Wall Mount Lav Mixer with Cross Handles 39143XX1 Axor Citterio Wall Mount Lav Mixer with Lever Handles 39147XX1 39143XX1 39147XX1 Technical Information Recommended water pressure Max. water pressure Recommended hot water temp. Max. hot water temp Flow rate 14.7 - 72.5 psi 145 120° - 140° F* 165° F* 1.5 gpm *Please know and follow all applicable local plumbing codes when setting the temperature on the water heater.
Installation Considerations • For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber. • Please read over these instructions thoroughly before beginning installation. Make sure that you have all tools and supplies needed to complete the installation. • Rough 10303181 must be installed, and the wall finished prior to installation of this trim kit. • This faucet does not include a drain.
All models: Remove the plug from the spout port. Install the handle slip coupling. Use a ruler to measure a point on the coupling 3/8" from the surface of the finished wall. Mark the coupling at that point. Cut the coupling. Insert the extension spindle. Use a ruler to measure to a point on the extension spindle ½" from the surface of the finished wall. Mark the extension spindle at that point. Cut the extension spindle. Push the handle into place. The handle should be parallel to the floor.
If it is not, remove it. Remove the extension spindle from the handle. Turn it slightly and reinsert it. Replace the handle. It should now be parallel to the floor. Remove the handle. Push the escutcheon over the slip coupling. Place the handle over the valve. Turn the handle base clockwise, so that it threads onto the slip coupling. Install the spout Use a ruler to measure from the metal part of the spout port to the outside edge of the plaster shield. Record the measurement (“x”). Add 1 7/8" to “x”.
Wrap the threads on the spout connector with several layers of Teflon tape. Screw the spout connector into the port. Measure the spout connector. It should extend from the plaster shield 1 3/8". Place the escutcheon over the spout connector. Press the spout over the connector. The pin on the back of the spout should align with the keyhole on the spout escutcheon. Use a 3 mm Allen wrench to tighten the set screw on the bottom of the spout.
Replacement Parts 10 11 1 5 12 14 3 7 6 9 15 13 4 8 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 handle, cross handle, lever seal hot escutcheon cold escutcheon spout escutcheon spout, 9" aerator handle fixing set spout connector hot cartridge cold cartridge set screw o-ring, 16 x 2.
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe"). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. This warranty is non-transferable.
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from State to State. You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnuson-Moss Warranty Act.
www.hansgrohe-usa.com US - Installation Instructions • Part No. 90614703 • Revised 01/2009 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.
