Hanover Outdoor Furniture IMPORTANT If you have any problems with this product (missing or damaged parts, assembly issues, etc.), PLEASE DO NOT RETURN TO THE RETAILER/STORE from where you purchased the product. Please call our Toll‐Free Customer Service Hotline at: 1‐800‐416‐3511 Between 9:00 AM and 5:00 PM Eastern Time, Monday through Friday Or visit our website at: www.hanover‐products.
Outdoor Furniture 1-Year Limited Warranty Program For a period of one (1) year after purchase, the Manufacturer will either repair or replace defective components in accordance with this Limited Warranty. This warranty is between Manufacturer and the original purchaser and is valid only when accompanied by the original purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty revert back to the date of original purchase for future warranty.
Care & Maintenance Outdoor furniture can be enjoyed for many years when well maintained. Regular Maintenance Wash the furniture with a solution of mild detergent and water, rinse with clear water, and dry thoroughly. To all metal frames, apply a fine, clear automobile wax for maximum protection against harmful ultraviolet exposure and salt air. For best protection, perform this maintenance two or three times per year in low pollution areas or more frequently in high pollution areas.
ASSEMBLY INSTRUCTIONS 1 Position the swivel base on a flat, solid surface. Make sure the swivel plate is positioned all the way into the base. It may have vibrated out during shipment. The two sets of holes in the swivel plate should be facing away from you. Note the arrows on both the swivel plate and the "U" bar portion of the chair frame.
PARTS IDENTIFICATION LIST * NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE PARTS LIST DESCRIPTION ORDER PART # QTY A CHAIR FRAME AB1267 1 B SWIVEL ASSEMBLY & BASE AB1268 1 C 5/16" X 43 MM BOLT HW0450 4 D Ø8.0 X 2.3 MM SPRING WASHER HW0003 4 E METAL PLATE HW0686 2 F 5/16" NUT HW0015 4 G BOLT COVER HW0028 4 H NUT COVER HW0109 4 I Ø8.5 X 1.
ASSEMBLY INSTRUCTIONS CSA Model WT17YP4 ARX13200 Installer: Leave these instructions with consumer. Consumer: Keep these instructions for future reference. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. WARNING: Improper installation, adjustment alteration, service or maintenance can cause injury or property damage.
TABLE OF CONTENTS Important Safety Information .................................................................3 Important Information about Propane....................................................4 Specification ..........................................................................................4 Parts Identification List ..........................................................................5 Installation ........................................................................................
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).
IMPORTANT SAFETY INFORMATION ABOUT PROPANE (LP) GAS A LP-gas cylinder for use with this appliance must have a capacity of 20 lbs / 9kg. and must be equipped with a Type 1 connector and an OPD (overfill protection device). Figure 1 The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S.
PARTS IDENTIFICATION LIST PART DESCRIPTION PART# QTY A CONTROL PANEL FP2187 1 B LP REGULATOR HOSE FP1916 1 C LP TANK RETAINING KNOB FP0585 2 D ADJUSTABLE FOOT CAPS FC0553 4 E PROPANE ORIFICE FP2205 1 F NATURAL GAS ORIFICE FP2206 1 G FIRE ICE FP2006 1 H AIR SHUTTER FP1922 1 I 1/4” X20 MM BOLT HW0036 4 J 1/4” X30 MM BOLT HW0038 12 K Ø6.5 X 1.0 MM WASHER HW0594 12 L Ø20 X Ø6.5 X 2 MM WASHER HW0901 4 M HEX BOLT DRIVER HW0006 1 N “AAA” BATTERY(1.
BURNER COVER V FP2221 1 INSTALLATION 1. Carefully unpack all items from the box. Place the base in the final position. There must be a minimum of 24 in / 60.96 cm of clearance from the side of the table top to any combustible walls. 2. Attach the bottom frame to the two side panels and the back panel by using six 1/4"x30 mm bolts and washers as shown in Figure 2a. Guide the bolts through the holes in the bottom frame, into the pre-drilled holes in two side panels and the back panel. Do not over tighten.
4. Pour the lava rocks or fire ice into the burner pan completely covering the burner. The weight of lava rocks is (3.6kg plus and minus 10%); the weight of the fire ice is (8kg plus and minus 10%). Remove any lava rocks or fire ice on top of the ignition well. See Figure 4. Figure 4 5. Remove the door panel and place the LP tank onto the bottom frame as shown in Figure 4. Connect the regulator as shown in Figure 4. Turn the black handle clockwise to tighten. Turn the handle counterclockwise to remove.
NATURAL GAS CONVERSION Natural gas conversion must be performed only by your natural gas provider or service company. 1. SHUT OFF THE GAS SUPPLY TO THE UNIT AND ANY NEARBY ELECTRICAL SOURCE OR APPLICANCES 2. Below the burner, carefully disconnect flex connector attached to the orifice holder (see step1). 3. Carefully unscrew the orifice holder from the burner pipe (see step2). 4. Remove the propane orifice from the holder and replace with natural gas orifice (see step2). 5.
9. Restore your gas supply and check ALL of the connections for leaks using a solution of soapy water. If a leak is discovered and any bubbles are seen, close the main gas valve and re-tighten ALL the connections. NEVER USE A FLAME TO CHECK FOR GAS LEAKS! Step5 10. Stick the conversion label on the rating plate as shown in Figure 6. Metal Rating Plate Model Number: WT17YP4 Serial Number _________________ CAUTION: The gas pressure regulator provided with this1.appliance must be used.
BATTERIES Make sure the control knob is in the "OFF" position. Unscrew the push button cap on the ignition module located on the control panel to access the battery compartment. The ignition module requires one Alkaline AAA size battery (1.5V). The negative (-) end goes in first. See Figure 8.Dispose of battery safely. May explode or leak if charged or disposed of in fire. Make sure of the polarity. Mercury and cadmium free.
should pop back out and then the fire remain lit. Note: If the fire does not light, turn the knob to the “OFF” position and wait five (5) minutes before trying again. 3. To turn down the flame, push the control knob in slightly and turn to Medium (medium flame), or Low (small flame). 4. To shut down the fire pit, turn the control knob to the “OFF” position and turn off the tank valve. TROUBLESHOOTING GUIDE PROBLEM CAUSE REMEDY No Propane Gas at Burner Check that gas tank valve is open.
ONE-YEAR LIMITED WARRANTY What is Covered Under This Warranty? The item you have purchased is warranted against defects in material and workmanship for the following parts from the date of purchase for the period of warranty as outlined below, but only when the unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes: Limited 1 Year • Stainless Tube/Plate burner Limited 90 days • All remaining parts How Do I Obtain Warrant
