PACKAGE CONTENTS Control Box Assy J Lower Support K Block Belt L Wheel Assembly M Bottom Plate N Led controller O PART A B C D E F G H I J K A Reflector B Flame Screen C Glass Tube D Upper Support E Protective Guard F Black Silicone Ring G Side Panel H Front Panel I DESCRIPTION Reflector Flame Screen Glass Tube Upper Support Protective Guard Black Silicone Ring Side Panel Front Panel Gas Hose & Regulator Control Box Assy Lower Support QUANTITY 1 1 1 4 4 1 PART L M N O 3 1 1 1
HARDWARE CONTENTS (shown actual size) AA BB Wing nut Qty. 3 GG CC Stud Qty. 3 Small flat washer Φ6 Qty. 6 HH Screw M5 X 12 Qty. 6 NN DD 3/16” Screw Qty. 42 JJ Fixing Bracket Qty. 4 LL Wrench Qty. 1 Philips screwdriver Qty. 1 MM Knob Qty. 1 PP Long Stem Lighter Qty.1 M6 Flange nut Qty. 4 Bolt M6 X 12 Qty. 4 KK OO Chain Qty.1 FF EE Screw M4 X 10 Qty.1 QQ Wafer Qty.1 AA Battery (1.5 V) Qty.
SAFETY INFORMATION DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces that do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
ASSEMBLY INSTRUCTIONS 1. Assemble the wheel assembly to the bottom plate. Fix the wheel assembly to the bottom plate using 4pcs bolt M6X12 and 4pcs flange nut M6. 1 Hardware Used EE Bolt M6 X 12 x4 FF M6 Flange nut x4 JJ Wrench x1 EE M FF 2-1. Unscrew the switch button, load small battery, tighten the switch button. 2-2. Insert the pins of the Bottom Plate to the holes of lower support, press to secure the pins. Using 4pcs screw M5x12 to secure the lower support and Bottom Plate.
ASSEMBLY INSTRUCTIONS 3.Assemble block belt. Fix the block belt to the 2pcs of lower support behind the front door,using 2pcs screw M5X12. 3 Hardware Used GG Screw M5 X 12 KK Philips screwdriver x2 x1 L GG 4 4. Assemble the middle support. Insert the 4pcs upper support to the lower support. Secure them with 8pcs screw 3/16”.
ASSEMBLY INSTRUCTIONS 5. Assemble the flame screen to the upper support. Secure the flame screen to the upper support using 8pcs 3/16” screw. 5 B Hardware Used DD 3/16” Screw x8 KK Philips screwdriver x1 DD 6. Assemble the reflector onto the flame screen. Screw the 3pcs stud on the flame screen, put 3pcs Φ6 washer onto the top of stud, then put the reflector onto the stud, secure them with 3pcs Φ6 washer and 3pcs wing nut.
ASSEMBLY INSTRUCTIONS 7. Carefully install the glass tube by lifting up and inserting through the center hole in the upper plate. Ensure the black silicone ring is attached to the lower edge of the glass tube as illustrated. Slide the glass tube through the hole of the lower plate cover and onto the middle plate. Check and ensure that the glass tube is positioned properly and is completely covering the center hole of the middle plate.
ASSEMBLY INSTRUCTIONS 9. Attach the three side panels to the heater using 18pcs 3/16” screw. Note : Do not cover the front side where the control knob is. 9 Hardware Used DD 3/16” Screw x 18 KK Philips screwdriver x1 10. Assemble the chain and wafer to the inside of front panel with M4x10 screw, then install the knob to M4x10 screw. Hang the chain to the hole on the control box assy and put the pothook of front panel to the holes of bottom plate.
ASSEMBLY INSTRUCTIONS 11. Screw gas hose and regulator to propane cylinder (not included). Do not cross-thread. WARNING: Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See chapter 5 of the standard for storage and handling of liquefied petroleum gas, ANS/NFPA 58. Your local library or fire department should have this book. A minimum supply pressure of 8” W.C. is required for the purpose of input adjustment for propane gas.
ASSEMBLY INSTRUCTIONS 12. LED belt box and battery box installation. 12-1. The normal position of block chip like 12 figure a. 12-2. Adjust the position of block chip like figure b. Pull out the LED belt box. 12-3. When chang the batteries, first take out the LED belt box and then battery box, after that open the battery box and Figure a change the batteries like figure c.
ASSEMBLY INSTRUCTIONS Operation Instructions of Controller 1. Specifications: Working temperature: -4-140 F( -20-60 C) Supply voltage: DC12V Product size: L2.44×W1.38×H0.9 inch Package size: L4.13×W2.56×H2.17 inch Net weight: 0.11 lbs Gross weight: 0.15 lbs Output: Three CMOS drain-open output Connecting Mode: Common anode Max Ioad current: 2 A each color 2.
ASSEMBLY INSTRUCTIONS WARNING: A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your propane supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
